15-29. In case of emergency, the gas actuator is used to move a 75-kg block B by exploding a charge C near a pressurized cylinder of negligible mass. As a result of the explosion, the cylinder fractures and the released gas forces the front part of the cylinder, A, to move B forward, giving it a speed of 200 mm/s in 0.4 s. If the coefficient of kinetic friction between B and the floor is Pk = 0.5, determine the impulse that the actuator imparts to B.

15-29. In case of emergency, the gas actuator is used to move a 75-kg block B by exploding a charge C near a pressurized cylinder of negligible mass. As a result of the explosion, the cylinder fractures and the released gas forces the front part of the cylinder, A, to move B forward, giving it a speed of 200 mm/s in 0.4 s. If the coefficient of kinetic friction between B and the floor is Pk = 0.5, determine the impulse that the actuator imparts to B.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

15-102. The two spheres each have a mass of 3 kg and are attached to the rod of negligible mass. Determine the time the torque M = (8t) N·m where, is in seconds, must be applied to the rod so that each sphere attains a speed of 3 m/s starting from rest
The double pulley consists of two wheels which are attached to one another and turn at the same rate. The pulley has a mass of 15 kg and a radius of gyration kO=110mm. If the block at A has a mass of 40 kg, determine the speed of the block in 3 s after a constant force F=2kN is applied to the rope wrapped around the inner hub of the pulley. The block is originally at rest. Neglect the mass of the rope.
17-74 The two blocks A and B have a mass Ma and Mb, respectively, where Ma > Mb. If the pulley can be treated as a disk of mass M, determine the acceleration of block A. Neglect the mass of the cord and any slipping on the pulley.
17-59 The uniform slender rod has a mass m. If it is released from rest when = 0, determine the magnitude of the reactive force exerted on it by pin B when = 90.
18-19 The 30 kg disk is originally at rest, and spring is unstretched. A couple moment M= 80 Nm is then applied to the disk as shown. Determine how far the center of mass of the disk travels along the plane before it momentarily stops. The disk rolls without slipping.
19-35 The 10 kg bullet having of 800 m/s is fired into the edge of the 5 kg disk as shown. Determine the angular velocity of the disk just after the bullet becomes embedded into its edge. Also, calculate the angle the disk will swing when it stops. The disk is originally at rest. Neglect the mass of the rod AB.
The smooth surface of the vertical cam is defined in part by the curve r =(0.2 cos θ + 0.3) m. The forked rod is rotating with an angular acceleration of 2rad/s^2, and when θ = 45° the angular velocity is 6 rad/s. Determine the force the camand the rod exert on the 2-kg roller at this instant. The attached spring has a stiffnessk = 100 N/m and an unstretched length of 0.1 m.
5. The 25-kg block AA is released from rest.
18-37 The spool has a mass of 20 kg and a radius of gyration of = 160 mm. if the 15 kg block A is released from rest, determine the velocity of the block when it descends 600 mm.
The 10-lb block A travels to the right at va= 2 ft/sec at the instant shown. If the coefficient pf kinetuc friction is uk = 0.2 between the surface and A, determine the velocity of A when it has moved 4ft Block B has a weight of 20 lb. (Unit in m/sec)
The trailer with its load has a mass of 200 kg and a center of mass at G. If it is subjected to a horizontal force of P = 1000 N, determine the trailer’s acceleration and the normal force on the pair of wheels at A and at B. The wheels are free to roll and have negligible mass.
The wheel has a mass of 100 kg and a radius of gyration of kO = 0.2 m. A motor supplies a torque M = (40u + 900) N #m, where u is in radians, about the drive shaft at O. Determine the speed of the loading car, which has a mass of 300 kg, after it travels s = 4 m. Initially the car is at rest when s = 0 and u = 0°. Neglect the mass of the attached cable and the mass of the car’s wheels