15 m 1.5m P= 0.8 kN T-12 kN 2m 15 m 3 m Determine the x-, y-, and z- components of T. Determine the angles which the line of action of T forms with the positive x-, y-, and z-axes. Calculate the projection of P onto a line between 4 and Fand determine the angle between P and AF. Determine the vector expression for the moment of P about point E.

15 m 1.5m P= 0.8 kN T-12 kN 2m 15 m 3 m Determine the x-, y-, and z- components of T. Determine the angles which the line of action of T forms with the positive x-, y-, and z-axes. Calculate the projection of P onto a line between 4 and Fand determine the angle between P and AF. Determine the vector expression for the moment of P about point E.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

state T(C) P(bar) V(cm^3/g) H(KJ/Kg) S(KJ/kgK) 1(initial) 2(after throttle) 3(after cooling) 4(after compressor) fill out the number in the table
A pump increases water pressure from 1 bar to 4 bar. If the flow rate of the water is 150 l/min, determine its power? a)750 W b)150 W c)600 W d)1000 W e)250 W
F = 100 Sin(wt) K = 112.5 lb/in M = .50 lb-sec²/in w = 15 rad/sec The displacement of the system shown below must be limited to 50 inches, measured from th static equilibrium position of the system. Determine approximately how long the system will run before it must be shut down. a. 0.1 sec b. 7.5 sec c. 2.0 sec d.75. sec e. 10 sec f. 50.0 sec g.none
Q1/ A conditioned room at 25C db, 50% RH have sensible load 54 kW and latent load is 6 kW. The difference between supply temperature and the room is 10C. calculate: a. Sensible heat factor. b. Supply volume flowrate. c. Supply conditions.
There are two double-acting pneumatic actuators, the extension of each one is executed in 5 seconds at 80 psi and recoil in 4 seconds at 30 psi, the travel of both is 12 inches, the diameter of the piston is dp = 4 "and of the rod dv = 1"a) Determine the compression ratios. The local atmospheric pressure is 79kpa = (11.5 psi)b) Determine the air consumption in cubic feet per minute of free air PCMc) Determine the average air consumption for each.d) Propose the regulation values of the pressure switch, system pressure and safety valve
An office for seating 30 occupants is to be maintained at 22°C DB and 55% RH. The outdoor conditions are 36°C DB and 27°C WB. The various loads in the office are: Solar heat gain = 8,500W; Sensible heat gain per occupants = 83 W; Latent heat gain per occupant = 100W; Lighting load = 2,500W; Sensible heat load from other sources = 12,000W; and Infiltration load = 15 m3/min. Assuming 40% fresh air and 60% of recirculated air passing through the evaporator coil and the by-pass factor of 0.12, determine the following: A) The Dew Point Temperature of the coil, in degrees Centigrade. B) The Capacity of the Airconditioning Plant, in Tons of Refrigeration.
Problem 1: A certain rigid aluminum container contains a liquid at a gauge pressure of P0 = 2.02 × 105 Pa at sea level where the atmospheric pressure is Pa = 1.01 × 105 Pa. The volume of the container is V0 = 2.15 × 10-4 m3. The maximum difference between the pressure inside and outside that this particular container can withstand before bursting or imploding is ΔPmax = 2.41 × 105 Pa.For this problem, assume that the density of air maintains a constant value of ρa = 1.20 kg / m3 and that the density of seawater maintains a constant value of ρs = 1025 kg / m3. Part (a) The container is taken from sea level, where the pressure of air is Pa = 1.01 × 105 Pa, to a higher altitude. What is the maximum height h in meters above the ground that the container can be lifted before bursting? Neglect the changes in temperature and acceleration due to gravity with altitude. Part (c) Choose the correct answer from the following options. The depth below the surface of the ocean…
A four-cylinder four-stroke petrol engine with the following specifications: - The bore(diameter) = 20 cm - The stroke = 30 cm - The compression ratio = 8 - The indicated power = 33 KW - The engine speed = 2500 rpm - The indicated thermal efficiency = 35% - The friction power = 25 kW - The calorific value ( heating value) = 42000 kJ/kg . Determine the following: a) The indicated mean effective pressure. b) Thermal efficiency. c) Specific fuel consumption per hour. d) The Torque (given K = 1.4)
A concentrating solar collector array with 42 modules each comprising a CLFR (refer to Figure 8.11) and an absorber tube is used for raising steam under the following operating conditions:• Superheated steam condition: p1 = 100 bars, t1 = 550°C, enthalpy h1 = 3500 kJ/kg (from h,s-diagram)• Feedwater temperature is t2 = 268°C and its enthalpy is h2 = cp t2 = 4.187 × 268 = 1122 kJ/kg• Direct (beam) normal insolation (DNI) at the system location Ib,N = 833 W/m2 • Aperture area of a single CLFR module Aap = 390 m2• Efficiency of the solar collector ηc = 0.71 Calculate (i) the rate of useful heat output of the CLFR array and (ii) therate of steam production.
8.a. When a machine is tested, the volume of cooling air is 1250 cfm. If the temperature of the entering air is 25 C and the temperature of the outgoing air is 35 C, the loss in the machine isA. 7.1 kw.B. 24.8 kw.C. 12.5 kw.D. 17.7 kw. 8.b. When a motor is tested with a prony brake, the scale reading is 3.50 lb. The length of the brake arm is12 in. and its weight is 0.50 lb. If the motor speed is 1700 rpm and the power input is 1050 watts, themotor efficiency isA. 80.5%B. 69%C. 75%.D. 64.5%.
An ideal spring has a spring constant k = 24.3 N/m. What is the amount of work that must be done to stretch the spring 0.800 m from its relaxed length? ________ J
Which system does more work: (a) ΔE= -436J, q= 400J, or (b) ΔE = 317 J, q= 347J?