ᴀ ꜱᴜᴍᴘ ᴘᴜᴍᴘ ᴛᴜʀɴɪɴɢ ᴀᴛ 1600 ʀᴘᴍ ᴘʀᴏᴠɪᴅᴇꜱ ᴀ ᴡᴀᴛᴇʀ ᴅɪꜱᴄʜᴀʀɢᴇ ᴏꜰ 9ɢᴘᴍ ᴀɢᴀɪɴᴛꜱ ᴀ ʜᴇᴀᴅ ᴏꜰ 18ꜰᴛ. ᴄᴏᴍᴘᴜᴛᴇ ᴛʜᴇ ᴍɪɴɪᴍᴜᴍ ᴘᴏᴡᴇʀ ɪɴᴘᴜᴛ. ᴜꜱᴇ ᴛʜᴇ ᴄᴜʀᴠᴇ ʙᴇʟᴏᴡ ᴛᴏ ᴅᴇᴛʀᴇᴍɪɴᴇ ᴛʜᴇ ᴇꜰꜰɪᴄɪᴇɴᴄʏ.

ᴀ ꜱᴜᴍᴘ ᴘᴜᴍᴘ ᴛᴜʀɴɪɴɢ ᴀᴛ 1600 ʀᴘᴍ ᴘʀᴏᴠɪᴅᴇꜱ ᴀ ᴡᴀᴛᴇʀ ᴅɪꜱᴄʜᴀʀɢᴇ ᴏꜰ 9ɢᴘᴍ ᴀɢᴀɪɴᴛꜱ ᴀ ʜᴇᴀᴅ ᴏꜰ 18ꜰᴛ. ᴄᴏᴍᴘᴜᴛᴇ ᴛʜᴇ ᴍɪɴɪᴍᴜᴍ ᴘᴏᴡᴇʀ ɪɴᴘᴜᴛ. ᴜꜱᴇ ᴛʜᴇ ᴄᴜʀᴠᴇ ʙᴇʟᴏᴡ ᴛᴏ ᴅᴇᴛʀᴇᴍɪɴᴇ ᴛʜᴇ ᴇꜰꜰɪᴄɪᴇɴᴄʏ.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 17RQ: Convert 22C to Fahrenheit.

See similar textbooks

Similar questions

The coefficient of bend value is the energy loss due to bend in a pipe depends on the pipe diameter, _________________, & radius of curvature of bend. Friction in the pipe bend Bend pipe material Length of the bend pipe Angle of bend
A closed pipe 3 ft long, compute the 6th harmonic if air temperatureis 80°F.a.627.92 Hzb. 1240.42 Hzc. 0d. 672.92 Hz
Need 5 points shear stress material material resistance
20mins plsss
The coefficient of bend value in the energy loss due to bend in a pipe depends on the radius of curvature of bend, _________________, & angle of bend.
The width of an apron conveyor with a capacity of 75 tons/hr & speed of 50 ft/min. a. 220 mm b. 370 mm c. 070 mm d. 460 mm
10 mile/h = ……… m/s (1mile = 1852m) Convert from FPS to SI.
W= 325 lbs/ft a= 6.8 ft
Compute for the Break Mean Effective Pressure with the following information: Given: Bhp = 1000 Stroke = 5 inches Bore = 5.5 inches Rpm = 2700 Number of cylinders = 8 *Show complete solution. Thank you.
ans: 0.01925kg, 0.7123kg, 1.886kPa Use gas laws
QUESTION 4 (Belt conveyors) 4.1 A coal conveyor belt is 900 mm wide and travels at 2,2 m/s. There are plans to build a surge bin to hold enough coal for two days' production. Calculate the bin capacity required if the bin is intended to hold coal produced in two eight-hour shifts. State any assumptions that you may make. 4.2 The following particulars apply to an inclined belt conveyor: Length of conveyor (loading end to discharge end): 100 mSpeed of belt: 1,5 m/sAngle of wrap around driving pulley: 220 degreesCoefficient of friction between belt and driving pulley: 0,3 Mass of rock conveyed (mass flow rate): 300 t/hThe discharge end is 22 m higher than the loading end. The total friction is equivalent to a force of 6,5 kN in the belt at the head pulley. The efficiency of the drive is 90%. 4.2.1 Calculate the power of the motor. 4.2.2 Calculate the minimum tension in the slack side of the belt as it leaves the driving pulley.
A small Passenger car has a 4 cylinder 2 litre engine. The swept volume of each cylinder is. 1)200cc 2)600cc 3)500cc 4)390cc