17. Given that L = 0.05 H in the circuit of Figure D, and the values of R and C as in problem 16, calculate the phase angle and magnitude of the impedance of the circuit at 100 kHz. (160 22. -90°) R FIGURED Circuit for problems 16, 17, and 18. 16. What value of L is necessary for resonance at 10,000 Hz for the circuit of Figure C when R = 57002 and C= 0.01 μF? (25 millihenries) only need question 17 answered use values R and C

17. Given that L = 0.05 H in the circuit of Figure D, and the values of R and C as in problem 16, calculate the phase angle and magnitude of the impedance of the circuit at 100 kHz. (160 22. -90°) R FIGURED Circuit for problems 16, 17, and 18. 16. What value of L is necessary for resonance at 10,000 Hz for the circuit of Figure C when R = 57002 and C= 0.01 μF? (25 millihenries) only need question 17 answered use values R and C

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter15: Alternating-current Circuits

Section: Chapter Questions

Problem 71CP: Shown below are two circuits that act as crude high-pass filters. The input voltage to the circuits...

See similar textbooks

Similar questions

An RLC series circuit has a 200 (resistor and a 25.0 mH inductor. At 8000 Hz, the phase angle is 45.0°. (a) What is the impedance? (b) Find the circuit’s capacitance. (c) If Vrms = 408 V is applied, what is the average power supplied?
An AC generator with an output rms voltage of 36.0 V at a frequency of 60.0 Hz is connected across a 12.0-F capacitor. Find the (a) capacitive reactance, (b) rms current, and (c) maximum current in the circuit. (d) Does the capacitor have its maximum charge when the current takes its maximum value? Explain.
In an LC circuit, what determines the frequency and the amplitude of the energy oscillations in either the inductor or capacitor?
The two circuits shown below act as crude low-pass filters. The input voltage to the circuits is vin, and the output voltage is vout. (a) Show that for the capacitor circuit, voutvin=11+2R2C2 and for the inductor circuit, voutvin=RR2+2L2 (b) Slow that for low frequencies, voutvin , but for high frequencies, vout0 .
At s1iat frequency is the reactance of a 20F capacitor equal to that of a 10-mH inductor?
(a) Does the phase angle in an RLC series circuit depend on frequency? (b) What is the phase angle for the circuit when the inductive reactance equals the capacitive reactance?
Check Your Understanding Show that the tins voltages across a resistor, a capacitor, and an inductor in an ac circuit where the tins current is Irmsare given by IrmsR,IrmsXC , and IrmsXL, respectively. Determine these values for the components of the RLC circuit of Equation 15.12. Pave=12t0v0cos (15.12)
Shown below are two circuits that act as crude high-pass filters. The input voltage to the circuits is vin, and the output voltage is vout. (a) Show that for the capacitor circuit, voutvin=11+1/2R2C2 and for the inductor circuit, voutvin=LR2+2L2 (b) Show that for high frequencies, voutvin , but for low frequencies, vout0 .
An RLC circuit connected across an AC voltage source at frequency f has resistance R, capacitive reactance XG and inductive reactance XL. If the frequency is doubled so that fnew = 2f, find the ratios (a) Rnew/R, (b) XC,new/XC, and (c) XL,new/XL.
At 1000 Hz, the reactance of a 5.0-mH inductor is equal to the reactance of a particular capacitor. What is the capacitance of the capacitor?
Describe what effect the resistance of the connecting wires has on an oscillating LC circuit.
can you help me draw a phasor diagram for this circuit that includes the impedance vector and the phase ange. Also, does the voltage in the current lead or lag the current