18 Consider fully developed flow in a circular pipe with significant entrance effects. If the length of the pipe is doubled, the head loss will: a. remain constant b. more than double double dless than double 19 Consider fully developed laminar flow in a circular pipe. If the diameter of the pipe is reduced by half while the flow rate and the pipe length are held constant, the head loss will a. double ..2 b. increase by a factor of 4 increase by a factor of 8 increase by a factor of 16 c.

18 Consider fully developed flow in a circular pipe with significant entrance effects. If the length of the pipe is doubled, the head loss will: a. remain constant b. more than double double dless than double 19 Consider fully developed laminar flow in a circular pipe. If the diameter of the pipe is reduced by half while the flow rate and the pipe length are held constant, the head loss will a. double ..2 b. increase by a factor of 4 increase by a factor of 8 increase by a factor of 16 c.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A clothes dryer discharges air at 1 atm and 120°F at a rate of 1.2 ft3/s when its 5-in-diameter, well-rounded vent with negligible loss is not connected to any duct. Determine the flow rate when the vent is connected to a 15-ft-long, 5-in-diameter duct made of galvanized iron, with three 90° flanged smooth bends. Take the friction factor of the duct to be 0.019, and assume the fan power input to remain constant.
A water fountain is to be installed at a remote location by attaching a cast iron pipe directly to a water main through which water is flowing at 70°F and 60 psig. The entrance to the pipe is sharp-edged, and the 70-ft-long piping system involves three 90° miter bends without vanes, a fully open gate valve, and an angle valve with a loss coefficient of 5 when fully open. If the system is to provide water at a rate of 15 gal/min and the elevation difference between the pipe and the fountain is negligible, determine the minimum diameter of the piping system.
1) Which of the following statement is NOT correct about piping network? a) In parallel pipes, the flow rate is proportional to its diameter and inversely proportional to its length and friction factor. b) When analyzing the piping network, conservation of mass throughout the system must be satisfied. c) In piping systems with pumps, the Bernoulli equation should be corrected by introducing a kinetic energy correction factor. d) The algebraic sum of head losses for all loops equal to zero. 2) The EGL is always a distance V2/2g above the HGL. True or False
A pipeline transporting engine oil of 3.5 m3/s at 40⁰C branches out into two parallel pipes made of commercial steel but reconnects downstream. Pipe A is 750 m long and has a diameter of 50 cm while Pipe B is 1200 m long with a diameter of 50 cm. Neglecting minor losses, determine the following:a) Flow rates (in m3/s) through pipe A and pipe B.(Hint: Assume similar flow frictional factor for initial calculations and determine the correct frictional factor using Colebrook equation).b) Actual head losses (in m) in pipe A and pipe B
Water at 16,2°C is to be discharged from a reservoir at a rate of 16,2 L/s using two horizontal cast iron (roughness value ɛ=0.00026m) pipes connected in series and a pump between them. The first pipe is 26,2 m long and has a 66,2 mm diameter, while the second pipe is 36,2 m long and has a 46,2 mm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged (KL=0.562), and losses associated with the connection of the pump are negligible. Neglecting the effect of the kinetic energy correction factor, determine the required pumping head, the minimum pumping power and electric motor power for total efficiency value of 76,2% to maintain the indicated flow rate. Water density is r=996,2 kg/m3, dynamic viscosity µ= 1.162x10-3kg/ms. Solve the problem by making the necessary assumptions and drawing the schematic figure.
[CE Hydraulics] Is the flow expected to be uniform or nonuniform for frictionless pipes? Why?
Determine the average velocity for water flow in a 2 in diameter pipe, Schedule 40 chlorinated polyvinyl chloride (CPVC) pipe (2.375 in outside diameter and 2.047 in inside diameter) carrying cold water at a volumetric flow rate of 40 gpm.
Consider flow from a water reservoir through a circular hole of diameter D at the side wall at a vertical distance H from the free surface. The flow rate through an actual hole with a slightly rounded entrance (KL = 0.12). is considerably less than the flow rate calculated assuming “frictionless” flow and thus zero loss for the hole. Disregarding the effect of the kinetic energy correction factor, obtain a relation for the “equivalent diameter” of the sharp-edged hole for use in frictionless flow relations.
Rate the flow inside a pipe with Re = 1.8x10^4 and ε/D = 0.027. A: Turbulent totally rough B. Hydraulically smooth turbulence C. Laminar, with f=64/Re D.Transient roughness turbulence
C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the pipeline. The diameter at the smaller end is 245 mm and at the larger end is 467 mm. The length of the conical tube is 1.8 m and the flow rate of the oil is 128 liters/s. The pressure at the smaller end is equivalent to a head of 9.7 m of oil. Considering the following two cases: (1) Neglecting friction, (without head loss) determine (i) the velocity at the smaller end in m/s, (ii) the velocity at the larger end in m/s, and (iii) the pressure at the larger end of the tube. (2) If a head loss (with head loss) in the tube is hL= 0.0153(V1-V2)2, where V1 is the velocity at the smaller end and V2 is the velocity at the larger end, determine (iv) the head loss in m of oil and (v) the pressure at the larger end of the tube.
Water is pumped from a reservoir to a pressurized storage tank (P = 150 kPa gauge) atop a building by means of a centrifugal pump. There is a 70-m difference in elevation between the water surface in the reservoir and the end of the discharge line. The piping system consists of 80m of 5" SCH 40 steel pipe containing two 90o elbows, one gate valve, one rotary water meter, and six couplings from the reservoir to the pump; 3" SCH 40 steel pipe for 86m to the tank. The 3" pipe contains two gate valves, four 90o elbows, and ten couplings. It is desired to maintain a flow of water into the tank of 2.4 m3/min. Water temperature is 25oC. If the pump-motor set has efficiency of 65%, what would be the pumping costs be in pesos per day if electricity costs PhP 10.50/kW-hr?
For fully developed laminar pipe flow, if the diameter of the pipe is decreased by a factor of 3 whereas the length of pipe and flow rate is kept fixed the head loss will …………. Please fill the blank with correct answer.