·1.00.T3ts=1 Sint-ISLOSESt's = ra sint, ~6= 1050₂and crosse= 8.00Y6881Eso22.52instandzin207771au VB4 = 46513/16DF·Zip61ra= 1, Sin18 Considerrotating shaft with imbalanus usshown. A single balancing muss is to helocated in the same plane as theimbalance masses.rotates @radlsshe the wolad sxvadail and g volt jelatno.MaHinn 24 (1) m7of intoxity 3030/1₂66dworgn's 31.xm₁ = 6 hy1₁=250mm•mation duwu am₂ = Ylly √₂=200mm | 2₁ thout a lossM3 = whg rz=200mmanotzil 23-thetto (oDolor Jelut:H1) for each muss. calculate centrifugal forceas well as its hor, & vert. components.(2) Determine magnitude and angular orientationof centr. force ass. with imbalane mases3) Deter. may, and angular orientation it loculed120mm

Given; m1=6 kg r1=250 mm θ1=120° m2=4 kg r2=200 mm θ2=60°m3=4 kg r3= 200 mm…

18) Consider rotating shaft with imbalanus as shown. A single balancing muss is to he located in the same plane as the imbalance masses. rotates @ woradls • wolad sendoll and je volt Hinnas (0) Mi 30 Tin oil of inlovitur sora dworgas 31. m₁ = 6 hg r₁=250mm my in d m₂ = 4lig √2=200mm | 21 fout w Cies m3 = whg r.3=200mm - anstall 25 full (e staffs ma tot X poole luite H 1) for each muss. calculate centrifugal force. as well as its hor, & vert. components (2) Determine magnitude and angular orientation of centr. force ass. with imbalane mases 3) Deter. may, and angular orientation it locule 120mm

18) Consider rotating shaft with imbalanus as shown. A single balancing muss is to he located in the same plane as the imbalance masses. rotates @ woradls • wolad sendoll and je volt Hinnas (0) Mi 30 Tin oil of inlovitur sora dworgas 31. m₁ = 6 hg r₁=250mm my in d m₂ = 4lig √2=200mm | 21 fout w Cies m3 = whg r.3=200mm - anstall 25 full (e staffs ma tot X poole luite H 1) for each muss. calculate centrifugal force. as well as its hor, & vert. components (2) Determine magnitude and angular orientation of centr. force ass. with imbalane mases 3) Deter. may, and angular orientation it locule 120mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 5 ft long solid SAE4340 OQT1000 steel shaft is required to transmit a power of 180 HP. The shaft speed is 3,000 rpm. The allowable shear stress is 50 ksi and the allowable angle of twist per foot of length is 0.04 radians. Determine the minimum diameter that meets the design requirements.
. Determine the angle of twist for the steel (AISI 4340, OQT 1200 F) hollow shaft with anoutside diameter of 40 mm and an inside diameter of 30 mm when transmitting 28 kWof power at a speed of 45 rad/sec. The shaft length is 400 mm
Design a hollow circular steel shaft to transmit an applied torque of 360,000 in-lbs. Theallowable shear stress is 6,000 psi and the inside diameter is to be 0.6 times the outsidediameter.
The torque transmitted by a solid shaft of diameter 10 mm and shear stress 75 MPa Select one: a. 14.72x109 N-m b. 14.72 kN-m c. 147.2 N-mm d. 14.72 N-m
A turbine shaft transmits 500 kW power at 900 rpm. The permissible shear stress is 80N/mm² while twist is limited to 0.5º in a length of 2.5 m. Take G = 0.8x10⁵ N/mm², on thebasis of torsional rigidity;i.Determine diameter of shaft if solid shaft is used.ii.If hollow shaft is chosen with di/do = 0.6, determine the suitable diameters of theshaft. please write with ball pen.. thank you
A 5 ft long solid SAE4340 OQT1000 steel shaft is required to transmit a power of 180 HP. The shaft speed is 3,000 rpm. The allowable shear stress is 50 ksi and the allowable angle of twist per foot of length is 0.04 radians. Determine the minimum diameter that meets the design requirements. Note- Shear modulus for steel is given in images
The maximum angle of twist on a 2.5 ft solid SAE1020 Cold drawn steel shaft can not exceed 0.35 degrees per foot length. The shaft is carrying 3,500 lb-in of torque. The allowable shear stress is 30 ksi. Find the minimum diameter required for the shaft.
A hollow shaft has to transmit 6MW at 150rev / min. The maximum allowable stress is not to exceed 60 MN / m? nor the angle of twist 0.3 ° per meter length of shafting. If the outside diameter of the shaft is 300 mm find the minimum thickness of the hollow shaft to satisfy the above conditions. G = 80 GN / m?
A hollow shaft has an inner diameter of 0.035 m and an outerdiameter of 0.06 m. Compute for the torque if the shear stress isnot to exceed 120 MPa in Nm.
A hallow steel shaft transmit 600km at 500 rpm.the minimum
campute the bending stress number for the goer pair described by the given data beLow. KS= 1, Km= 1,21, F= 2.00 in, DP= 3,33 in, NG= 70, Np=20 hp = 1750v. p.m, Av=11, Pd =6, Tp= 900ib V1= 1527 ft/min The matarial used for pinion a gear is cast iron
Q.12A solid shaft of diameter 'd' and length " issubjected to torque T. Another shaft B ofsome length, material but twice the diameter is subjected to the torque 2T. The ratio of the angle of twist of shaft A to shaft B is-