18. How far off from the center of the support is the center of the two holes in the bosses of the uprights?

Q: 4 A water Pipe is to beconstructed with a 20% grade in the novth divection and a 10% grade in the…

A: Given:- First pipe is constructed with 20% grade in the north direction. It means it has a slope…

Q: Direction. Draw the Force Sody Diagram of he tollowing iustrations. Lund

A: Draw the free body diagram for the given figures.

Q: C.W. ;DRAW: 1-FRONT+TOP+RIGHT SIDE 2-FRONT SECTION+TOP SECTION FROM MIDD. +RIGHT SECTION FROM MIDD.

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Determine the size of the shaft,

A: Given: P=22 kW N=550 rpm shear stress=42 MPa Tensile/compressive stress=56 MPa P=900 N L=2.5 m To…

Q: Principal nd Use 3

A: Given data

Q: find the requird fillet Size Ch) for figew soンル2 ん。 レン46cm 26cm /2

A: Given data: -  The shear stress for all joints is τ = 0.5 MPa. The length L is L = 40 cm. The…

Q: machined surface. Determine the plate thickness t) for infinite life.

A:

Q: . Determine the outside diameter of the shaft?

A: Given data, Inner diameter of the shaft,di=0.6 times the outer diameter,  Where, Modulus of…

Q: Redraw when the rack AB is at 45o angle. What are the other two angles belonging to the triangle…

A:

Q: ged parabolic arc the max, bendin

A:

Q: 7 - Which is not a type of freight car? A) safe

A: Option (e) is correct. high edged is not a type of freight car.

Q: y b a a = 9 in b = 1.2 in с 3 2.4 in

A: Find the centroid distance in inches.

Q: A toggle clamp used for securing a workpiece during a machining operation. Analytically determine…

A:

Q: d the enerry Jost in the slippin

A:

Q: Determine the angle of rotation at the free end.

A: Given: To determine: The angle of rotation at the free end due to the torque applied

Q: find the three views of the adjusting bracket

A: List of three view are shown below: 1.

Q: 5.53 A 15-mm-diameter hole is drilled in a piece of 20-mm-thick steel; the hole is then countersunk…

A: Given: where x-Centroid distance from the axis

Q: Deformed length of the elongated diagonal.

A: Given; A rectangular region in a solid is in a state of plane strain.   The rectangle is subjected…

Q: 40 kN 60 kN 30MATHalino.oom w/

A: FBD and Direction of friction forces as the 3 masses are there so we divide in 3 section for free…

Q: What does the moment-area method provide?

A: Solution:

Q: angle angle and 3 1 ween two bearin

A:

Q: Does this machine maximize or minimize the force (100 Ib) *

A: Reaction force acting on the point B is RB×1.5=100×20RB=1333.33 lb As the reaction force acting at…

Q: Redraw when the rack AB is at 89o angle. What are the other two angles belonging to the triangle…

A: When the rack AB is at 89o angle. Draw the diagram as given above.

Q: angle of twist (a) between A and B, (b) between B and C, um (c) At C

A:

Q: deformed length of the elongated diagonal

A: Given; Rectangular region in a solid is in a state of place strain.(X,Y) coordiantes of the corners…

Q: When the fulcrum is in the middle the force and distance are ____. A. The same at the ends  B.…

A: when the fulcurum is in  the middle the force and distance are the same at the ends.

Q: IS determine the weight of the combine system

A: To determine the Weight of combine system.

Q: B C b Hinge 20.0 c

A: Length of the loop (l) = 35.0 cm = 0.35 m Width of the loop (w) = 20.0 cm = 0.20 m Current in the…

Q: Construct a solid model of the wooden lamp base show t can be constructed by revolving the sketch…

A: write the technique to make a strong model of the wooden lamp based. 1. Click on sketch commamd by…

Q: The tool is shaper machine is fixed axis. O a. Z O b. A O c. Y O d. X

A:

Q: Assignment Find the centre of area (centroid) of the following figures. 4 in.- 5 in. in. 2 in. -1…

A: Dear student,                     According to the guidelines I am allowed to answer only one…

Q: Determine the cross sectional

A: Given; In an arc welding process welding speed is doubled. Assuming all other process parameters to…

Q: clastic (b) Please find the slope at A,

A:

Q: For machine element, locate the centeroid

A: Answer:  Centroid ( 44.78 , 27.19 , 26.25 ) For a step-by-step solution have a look through the…

Q: perpendicular to the plane of the gear The side surface above the pitch cirnd de surface above thee…

A: Option d is correct.

Q: Determine the thickness at the end of the plate.

A: For laminar flow over flat plate;Boundary layer thickness at the end of the plateof the length L is…

Q: Find the Diameter of the shaft

A:

Q: What is x bar centroid (from left edge of part over to centroid)?

A:

Q: Homework Draw (i) the sectional view from the front and (ii) the view from the left of the sliding…

A:

Q: Determine the flange thickness if the

A: To find Flange thickness

Q: Design the rod. (Find the diameter d).

A:

Q: If blocking is needed to support the load at its new location, it should be prepared __________.…

A: Blocking is used to prevent the load from lateral movement. The lateral movement is front and back,…

Q: e, what is the cube's weight?

A: To find Weight of cube

Q: Draw the front and right vlews of the solld below. Front Right

A: The front view and side view of the figure shown above will look exactly same. In both, the views…

Q: determine the radius of the fillets

A: Given: P=10 kN Breadth of the plate, D= 96 mm Diameter of the hole, d'= 9 mm Thickness of the…

Q: rad/sec and having 20 te sure angle is 20° and m. on at the centre of the sha

A:

Q: reight of the rods and for the leflection (a) of point C, anč

A: given:

Q: e radius of the curve?

A: To determine Radius of curve

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.