A spur pinion rotating at 20 rad/sec and having 20 teeth transmits 20 kWto a gear wheel. The pressure angle is 20° and module is 20mm. Thereaction exerted by the pinion at the centre of thc shaft is

Answered: Image /qna-images/answer/f586a7b2-e1b4-4607-8840-9bb7259daae7.jpg

Answered: rad/sec and having 20 te sure angle is…

Engineering

Mechanical Engineering

rad/sec and having 20 te sure angle is 20° and m. on at the centre of the sha

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A spur pinion of pitch diameter 50 mm rotates at 200 rad/s and transmits 3 kW power. The pressure angle of the tooth of the pinion is 20°, what is the total force exerted by a tooth of the pinion on the tooth on a mating gear?
pinion having 20 involute teeth of module pitch 6 mm rotates at 200 r.p.m. and transmits 1.5 kW to a gear wheel having 50 teeth. The addendum on both the wheels is 1/4 of the circular pitch. The angle of obliquity is 20°. Find (a) the length of the path of approach ; (b) the length of the arc of approach; (c) the normal force between the teeth at an instant where there is only pair of teeth in contact.
8.7 A pair of involute gears with 16° pressure angle and 6 mm module is in mesh. The number of teeth on pinion is 16 and its rotational speed is 240 r.p.m. When the gear ratio is just 1.75, find, in order that the interference is just avoided, (a) the addenda on pinion and gear wheel (b) the length of path of contact, and (d) the maximum velocity of sliding of teeth on either side of the pitch point. (DAV Indore, 1989) (Ans. a, 9.6 mm; a 4.2 mm; 35.41 mm; V = 95.58 cm/s) %3D
A spur pinion of pitch diameter 50 mm rotates at 200 rad/s and transmits 3 kW power. The pressure angle of the tooth of the pinion is 20° Assuming that only one pair of the teeth is in contact the total force (in Newton) exerted by a tooth of the pinion on the tooth on a mating gear is...
Please answer part 2, A 20° full depth involute spur pinion of 4 mm module and 21 teeth is to transmit 15 kW at 960 rpm. Its face width is 25 mm. 1.The tangential force transmitted (in N) is (a) 3552 (b) 2611 (c) 1776 (d) 1305 2. Given that the tooth geometry factor is 0.32 and the combined effect of dynamic load and allied factors intensifying the stress is 1.5 the minimum allowable stress for the gear material in MPa is, (a) 242.0 (c) 121.0 (b) 166.5 (d) 74.0
Qv quality number for camberless straight bevel pinion gear with 20 teeth and a modulus of 4 mmis 6. Made of 1st quality steel, with a hardness of 300 HB, the pinion and the reciprocating gear are completelyhardened. The rotated gear has 60 teeth. Pinion life is 109 cycles and reliabilitycoefficient is 0.999. Shaft angle is 90o, pinion rotation speed is 900 rpm. Tooth width 32 mm andThe normal pressure angle is 20o. Based on AGMA bending strength, the strength of the gear systemcalculate. Load factor Ko =1, safety factor SF =1.
A 20◦ helical gear has tangential force of 200lb and helix angle of 16◦ and face width of 0.6”.If the machining error is 0.6 and pitchline velocity is 400ft/min. Determine radial force, axial force, normal force, normal pressure angle and dynamic load.
For the gear mechanism in the figure: P1 = 4 kW, η1 = 1000 rpm, z1 = 18, z2 = 36, z3 = 54, z4 = 108, z1 is the driving gear. Total efficiency values for each stage; Since η12 = η34 = 0.96; Find the output torque and speed of gear z4.
A 15 kW and 1200 motor drives a compressor at 300 a pair of spur gears having . The center-to-center distance between the shafts is 400 . The motor pinion is made of forged steel having an allowable static stress as 210 MPa, while the gear is made of cast steel having allowable static stress as 140 MPa . Assuming that the drive operates 8 to 10 hours per day under light conditions , find from the standpoint of strength Module , 2. Fare and 3. Number of teeth and pitch circle diameter of each gear 2. Check the gears thus designed from the consideration of Static tooth load or endurance strength of the tooth flexural endurance limil (sigma_{\epsilon}) may be taken as 400 MPa 3. Check the gears thus designed from the consideration of wear surface endurance limit ( sigma epsilon x ) may be taken 700 MPa b ^ pi ( 6.154 - 0512/pi; F_{N}
Colegio de Muntinlupa fabricated a pair of spur gear 2.5 module (20° full depth involute tooth) and to be mounted on shafts with a centerline distance of 90 mm. The speed ratio required is 3:1. Determine the following: a. Pitch diameter of pinionb. Pitch diameter of gearc. Number of teeth of piniond. Number of teeth of geare. Circular pitch of pinionf. Circular pitch of gearg. Addendumh. Dedendumi. Clearancej. Whole depthk. Working Depthl. Backlashm. Tooth thicknessn. Tooth space widtho. Outside diameter of pinionp. Outside diameter of gearq. Root diameter of pinionr. Root diameter of gears. Base diameter of piniont. Base diameter of gear
A pair of 20 degree full depth spur gears have module of 2.5 and to be mounted on shafts with center distance of 90mm and gear ratio of 3. Find : $ if there is an interference $length of action and contact ratio $ if centher ditance was increased by 3mm, find backlash produced
A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth are to transmit 10 hp at 1500 rpm of a 4-in pinion having a total number of 28teeth. The velocity ratio desired is about mw = 4. Find the (a) normal circular pitch, (b) normal diametral pitch, (c) axial pitch, and (d) dynamic load