Please help us out 180 Problem:From the figure shown the coefficients offriction are as follows: 0.25 at the floor, 0.30 atthe wall and 0.20 between blocks.500 KN601000 kNO Which of the following gives the value ofthe reaction between the two blocks.2 Which of the following gives the reactionbetween the floor and the lower block.3 Which of the following gives the minimumvalue of a horizontal force P applied to thelower block that will hold the system inequilibrium.3

Answered: Image /qna-images/answer/bc3f00ba-accd-4897-86bb-47e3154a0a52.jpg

Answered: 180 Problem: From the figure shown the…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the magnitude (N) of the horizontal component of the reaction at point A if, F=500N, a=0.1m, b=2m, r=1.5m and d=30degrees
1. What is the reaction at point A? 8.0 KN 12.0 KN 10.0 KN 20.0 KN 2. What is the reaction at point C? 12.0 KN 8.0 KN 10.0 KN
Knowing that at the instant shown assembly A has a velocity of 9 in./s and an acceleration of 15 in./s2both directed downward, determine (a) the velocity of block B, (b) the acceleration of block B
A 1,100–N uniform boom at ? = 58.0° to the horizontal is supported by a cable at an angle ? = 32.0° to the horizontal as shown in the figure below. The boom is pivoted at the bottom, and an object of weight w = 2,050 N hangs from its top. Answer parts a-b.
SHOW COMPLETE SOLUTION AND FINAL ANSWER INTO 3 DECIMAL PLACES 3. A large pipe called penstock in hydraulic work is 1.5 m in diameter. Here it is composedof wooden staves bound together by steel hoops each 300 mm2in cross sectional area, and is used to conduct water from a reservoir to a powerhouse. If the maximumtensilestress permitted in the hoops is 130 MPa, what is the maximum spacing between hoops under a head of water of 30m? Use density of water equal to 1000 kg/m3
A steel tape with a cross-sectional area of 0.03 sq. cm is 50.00 m long under a pull of 5 kg when supported throughout its length. It measures a line 857.63 m long under a steady pull of 10 kg. Assuming E = 2.0 x 10 to the power of 6 kg/sq. cm, what is the elongation of the tape due to the increase in tension? a. 0.0250 m b. 0.0024 m c. 0.2500 m d. 0.0042 mShow solution please
Determine the magnitude of the horizontal reaction (N) at A if P = 255 N and Q = 1990 N. Let x = 2.45 m, y = 2.56 m, and z = 2.06 m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of the horizontal reaction at A: use R if to the right and L if to the left.
On a rough surface, Daniel pushes a carton with a mass of 30.0kg. The force F that is he applies is 608N with an angle of 55.0 degrees with the horizontal. In a time of 4s, the block's speed increases from 0.15m/s to 2.68m/s. a) Draw a free body diagram for your calculations b) Find the coefficient of kinetic friction between the flood and the block.
Please reply ASAP. Will rate immediately. Which of the following gives the horizontal reaction at point C?
Calculate the magnitude of the resultant couple moment.
For item #3. What is the moment due to the reaction force at A? 192.5 KN-m 157.5 KN-m 175.0 KN-m 82.5 KN-m For item #4. What is the moment due to the reaction force at D? 112.5 KN-m 137.5 KN-m 125.0 KN-m 202.5 KN-m For item #5. What is the moment due to the point load at B? –80.0 KN-m –120.0 KN-m –140.0 KN-m –150.0 KN-m What is the Area at A1? 673.75 KN- m² 551.25 KN- m² 123.75 KN- m² 192.5 KN- m² What is the Area at A2? 281.25 KN- m² 343.75 KN- m² 911.25 KN- m² 112.5 KN- m² What is the Area at A3? –160.0 KN- m² –240.0 KN- m² –490.0 KN- m² –375.0 KN- m² What is the deviation of point C to the tangent drawn from point A, tC/A? What is the deviation of point D to the tangent drawn from point A, tD/A? What is the deflection at point C, δC?
F1=432N,187.5 F2=111N,287.5 F3=345N,87.5 F4=234N,87.5 F5=123N,17.5 what is the resultant of the forces?

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

180 Problem: From the figure shown the coefficients of friction are as follows: 0.25 at the floor, 0.30 at the wall and 0.20 between blocks. 500 KN 60 1000 kN