19. A compressed liquid in a container has a volume of 1 liter at a pressure of 1 MPa and a volume of 0.995 liter at a pressure of 2 MPa. What is the bulk modulus of elasticity of the liquid? * 150 MPa 200 MPa 210 MPa 220 MPa 20. What pressure is required to reduce the volume of water by 0.60 percent If the volume modulus of elasticity of water is 2.2 GPa? * 10.5 MPa 11.2 MPa 12.5 MPa 13.2 MPa

19. A compressed liquid in a container has a volume of 1 liter at a pressure of 1 MPa and a volume of 0.995 liter at a pressure of 2 MPa. What is the bulk modulus of elasticity of the liquid? * 150 MPa 200 MPa 210 MPa 220 MPa 20. What pressure is required to reduce the volume of water by 0.60 percent If the volume modulus of elasticity of water is 2.2 GPa? * 10.5 MPa 11.2 MPa 12.5 MPa 13.2 MPa

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter6: Fundamental Dimensions And Units

Section: Chapter Questions

Problem 35P

See similar textbooks

Similar questions

A 10 cm long rectangular bar (when subjected to a tensile load) deforms by 0.1 mm. Calculate the normal strain.
A structural member with a rectangular cross section as shown in the accompanying figure is used to support a load of 2500 N. What type of material do you recommend be used to carry the load safely? Base your calculations on the yield strength and a factor of safety of 2.0.
Determine the Bulk modulus of elasticity of a liquid, which is compressed in a cylinder from a volume of 0.0125 m3 at 80 N/cm2 pressure to a volume of 0.124 m3 at 150 N/cm2 pressure ?
12) What pressure is required to reduce the volume of water by 0.6 percent? Bulk modulus of Elasticity of water, EB is 2.2 GPa. 13) A rigid container is partially filled with liquid at 15 atm. The volume of liquid is 1.232 L. At a pressure of 30 atm, the volume of liquid is 1.231 L. Find the bulk modulus of elasticity of the liquid over the given range of pressure if the temperature after compression is allowed to return to its initial value. What is the coefficient of compressibility? Note: 1 atm = 101.325 kPa.
A liquid compressed in a cylinder has a volume of 1000 cm3 at 0.95 MN/m2 and a volume of 1000 cm3 at 2.19 MN/m2. What is its bulk modulus of elasticity in MPa? Round off your answer to two decimal places.
1. If K = 2.2 GPa is the bulk modulus of elasticity for water, what pressure is required to reduce a volume by 0.6 percent? 2. A liquid is compressed. The change in pressure is 1000 psi. The change in density is 0.02%. What is the bulk modulus in psi? 3. The temperature of liquid water decreases from 80°C to 20°C. The percent change in absolute viscosity is ?
The Bulk Modulus of Elasticity of water us approximately 311 000 psi. If the temperature is 60°F, determine the pressure that should be applied so that the ratio of the change of volume with its initial is 2.5%. Use ?? = − ??/ ?? / ?and 2 decimal places.
Show complete solution with figures A rigid container having outside diameter of 30 mm and thickness of 5 mm contains water of height 700 mm.What will the column length be if a force of 5 kN is applied to its open end by a frictionless plunger? Assume noleakage. Use 2.2 GPa for bulk modulus of elasticity of water. a) 689 mm b) 525 mm c) 527 mm d) 695 mm e) None
Steve Roger measured a line and found it out to be 950 m long using a 20 – m tape under a steady pull of 4 kg at a mean temperature of 25°C. The tape was held in the air and supported at both ends and at the center. Determine the correct length of the line if the tape used is of standard length at 22°C under a pull of 6 kg. Assume the cross-sectional area of tape to be 0.05 cm2, modulus of elasticity as 2.10 x 10^6 kg/cm^2, weighs 0.08 kg/m, and a Coefficient of Thermal Expansion to be 0.0000116/°C.
A solid brass sphere of volume 0.305 m3is dropped in an ocean, where water pressure is 2 x 107 N/m2. The bulk modulus of water is 6.1 x 1010 N/m2. What is the change in volume of the sphere?
Calculate the pressure increase that must be applied to water to reduceits volume by 0.8%. Bulk Modulus of elasticity of water, Ev = 2.14 GPa.
5. A rigid steel container is partially filled with a liquid at 15 atm. The volume of the liquid is 1.23200 L. A a pressure of 30 atm, the volume of the liquid is 1.23100 L. Find the average bulk modulus of elasticity of the liquid over the given range of pressure if the temperature after compression is allowed to return to its initial value. What is the coefficient of compressibility? (3 DECIMAL IN FINAL ANSWER PLS!!)