19-3. Show that if a slab is rotating about a fixed axisperpendicular to the slab and passing through its masscenter G, the angular momentum is the same whencomputed about any other point P.P.

Given: The center of mass is at point G. In this case, linear velocity is zero as there is no…

Answered: 19-3. Show that if a slab is rotating…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

19-35 The 10 kg bullet having of 800 m/s is fired into the edge of the 5 kg disk as shown. Determine the angular velocity of the disk just after the bullet becomes embedded into its edge. Also, calculate the angle the disk will swing when it stops. The disk is originally at rest. Neglect the mass of the rod AB.
17-95 The 20 kg punching bag has a radius of gyration about its center of mass G of kG = 0.4 m. If it is initially at rest and is subjected to a horizontal force F = 30 N, determine the initial angular acceleration of the bag and the tension in the supporting cable AB.
The 30-kg turbine disk has a centroidal radius of gyration of 175 mm and is rotating clockwise at a constant rate of 60 rpm when a small blade of weight 0.5 N at point A becomes loose and is thrown off. Neglecting friction, determine the change in the angular velocity of the turbine disk after it has rotated through (a ) 90°, (b ) 270°.
The thin 12 kg bar has an angular velocity in a clockwise direction ω = 1.5 rad/s when in position shown. Determine its angular acceleration and the normal reactions of the smooth surface A and B at that time. i = (1/12) M . L² for a homogeneous thin bar of mass M and length L.
If the cord is subjected to a horizontal force of P = 150 N, and gear is supported by a fixed pin at O,determine the angular velocity of the gear and the velocity of the 20-kg gear rack in 4 s, starting from rest. The mass of the gear is 50 kg and it has a radius of gyration of k0 = 125 mm. Assume that the contact surface between the gear rack and the horizontal plane is smooth.
The uniform plate of mass m rotates about its corner O with the angularspeed ω. Determine the angular momentum of the plate about (a) the mass center;(b) the corner O; and (c) the corner A.
The assembly weighs 10 lblb and has a radius of gyration kGkGk_G = 0.60 ftft about its center of mass GG. The kinetic energy of the assembly is 25 ft⋅lbft⋅lb when it is in the position shown. (Figure 1) If it rolls counterclockwise on the surface without slipping, determine its linear momentum at this instant.
The body and bucket of a skid steer loader has a weight of 2000 lb, and its center of gravity is located at G. Each of the four wheels has a weight of 100 lb and a radius of gyration about its center of gravity of 1ft. If the engine supplies a torque of M = 100 lb ft to each of the rear drive wheels, determine the speed of the loader in t = 10 s starting from rest. The wheels roll without slipping
The 100-kg spool is resting on the inclined surface for which the coefficient of kinetic friction is μk = 0.11. The radius of gyration about the mass center is kG = 0.26 m Determine the angular velocity of the spool, measured clockwise, when t = 7 s after it is released from rest.
The rod assembly is supported by a ball-and-socket joint at C and a journal bearing at D, which develops only x and y force reactions. The rods have a mass of 0.7 kg/m. Determine the angular acceleration of the rods and the components of reaction at the supports at the instant w=9 rad/s as shown.
The spool has a mass of 20 kg and a radius of gyration of kO = 160 mm If the 15-kg block A is released from rest, determine the velocity of the block when it descends 850 mm .
The rod AB has a mass of 20 kg，the mass of the piston A and B are both 5kg. Piston B is attached to a spring of constant k = 1200 N/m. The spring is un-stretched when θ = 0. If the rod is released from rest whenθ = 45° Please find÷ (1) the moment inertia of the rod AB about its mass center G (2)The angular velocity of rod AB at θ = 0° (3）the velocity of piston A at θ = 0° (4) the velocity of Piston B at θ = 0° (hint: regard the piston A, B, rod as a system, during the motion, except the spring, the weight of rod AB, the weight of pistonB also does work). g = 9.8 m/s2

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

19-3. Show that if a slab is rotating about a fixed axis perpendicular to the slab and passing through its mass center G, the angular momentum is the same when computed about any other point P. P.