1)For this continuous beam, draw the qualitative and quantitative influence lines of the following using the Muller- Breslau Principle: a) Reaction at B b) Shear at the midspan of beam AB (Hint: use the reaction at B) c) Compute the reaction at B due to a moving concentrated load of 80 kN and a moving uniform load of 10 kN/m acting at span AB only. 2- 0.8 Ih 8m 8m

1)For this continuous beam, draw the qualitative and quantitative influence lines of the following using the Muller- Breslau Principle: a) Reaction at B b) Shear at the midspan of beam AB (Hint: use the reaction at B) c) Compute the reaction at B due to a moving concentrated load of 80 kN and a moving uniform load of 10 kN/m acting at span AB only. 2- 0.8 Ih 8m 8m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter9: Application Of Influence Lines

Section: Chapter Questions

Problem 2P

See similar textbooks

Similar questions

From the given beam in the figure, compute the maximum moment (kN-m, magnitude only) at C due to a uniform dead load of 14 kN/m, uniform live load of 14 kN/m and a concentrated load of 96 kN by influence lines. Use a = 3 m., and b = 10 m.
A 5 m long cantilever beam carries a uniform load of 5 KN/m on the 3 m portion of the beam from the free end and a counterclockwise couple of 60 KN -m acting at 1 m from the fixed support. Which of the following nearly gives the value the vertical reaction at the fixed point in KN and the value of the moment at midspan? Vertical fixed point: a. 15kn b. 20kn c. 5kn d. 10kn moment at midspan a. 22.5kn b. 45kn c. 15kn
A 15 m long beam AB has a fixed support at A and a roller at 10 m from A. If the free end is subjected to a concentrated load of 20 kN acting vertically downward. 1. Which of the following the value of reaction at roller support? a. 45 kN b. 35 kN c. 25 kN d. 20 kN 2. Which of the following gives the value of fixed end moment. a. 50 kN-m b. 40 kN-m c. 45 kN-m d. 38 kN-m
The beam in the figure below is to be loaded with 32.2 kN single axle load, a uniformly distributed live load of 49 kN/m, and a uniformly distributed dead load of 22 kN/m. Considering the loads, draw the influence lines and determine the following. - Maximum Vertical Reaction at C in kN - Maximum Negative Shear at B in kN. - Maximum Positive Shear at B in kN. - Maximum Positive Moment at B in kN-m.
For the girder shown below, draw the influence lines for shear in panel CD and the bending moment at point D. Then, determine the moment of point D due to the live load group and a uniformly distributed load of 50 kN/m if the system of loads will be moved to the right.
A propped beam has a span of 9 m. and carries a concentrated load of 60 kN at point B. E = 15000 MPa, I = 150x10⁶ mm⁴. 1. Which of the following gives the reaction at C. a. 32.12 kN b. 33.67 kN c. 34.87 kN d. 31.11 kN 2. Which of the following gives the slope at C in degrees. a. 4.58° b. 3.45° c. 3.44° d. 4.34° 3. Which of the following gives the deflection at B. a. -0.133 mm. b. -0.335 mm. c. -0.178 mm. d. -0.335 mm.
A 12m beam will be subjected to the followinh loads: Uniform dead load due to self weight = 19.7 kN/m Moving concentrated live load =268.8kN Moving concentrated uniform live load = 29.5 kN/m Determine the total maximum positive shear at C due to the given loadings Take the influence line ordinates aboce the x-axis as positive, and as negative Answer: 292.35 Need solution
Draw the influence line diagram of the given beam below for it's shear andmaximum moment about the point E, and determine the equivalentmaximum moment at point E due to a dead load of 10 kn/m and a movinglive load of 8 kn/m with two concentrated load of 90 kn and 80 kn that is 1mapart.ILD for Ve=f(x) and Me=f(x), (Point D is an internal pin)A. The maximum positive and negative ordinate of the influence linediagram from Ve=f(x)B. The maximum positive and negative ordinate of the influence linediagram from Me=f(x)C. The equivalent maximum moment of Me which is 4m away from the hingesupport due to the applied loading conditions?
Using Muller-Breslau principle sketch the influence line for i. Support reaction at Aii. Shear at 1.5m from A
For the beam shown below, determine the maximum shear (in kN, magnitude only) at point C due to a concentrated live load of 130 kN, a uniformly distributed live load of 52 kN/m, and a uniformly distributed dead load of 20 kN/m. Use the concept of influence lines. Point C is midway between supports B and D. Use a = 3 meters.
What is the positive max. moment at span AB? a. 25.80 kN-m b. 20.80 kN-m c. 23.80 kN-m d. 15.373 kN-m The positive maximum moment at span AB is located at a distance of _________ from support A. a. 2.50 m b. 1.203 m c. 2.056 m d. 1.503 m
In influence line for vertical reactions at support A and the moment at point B of the beams are shown. From the influence line of support A, what is the value of Ay when x = 4.20 m due to a unit load?