For the ideal-diode clipper circuit given below, VS = 12.sinwt V.a. Determine the output voltage Vout and sketch this function.b. Remove the short circuit between points x and y, and replace it with a 2k2 Resistor. Find the range of valuesof VS for;D1 and D2 are OFFD1 is ON and D2 is OFFD1 is OFF and D2 is ONIs it possible for both D1 and D2 to be ON?y1kO3VD2VS3kQ.VoutD16V

Given, Vs=12 sinwt V (a) D1 and D2 both are OFF V=IRHere,Req=1kΩ+3kΩVs=IReqI=VsReq =12sinωt4×103 =3…

Answered: 1kO 3V D2 vs 3kN. Vout D1 6V +

Engineering

Electrical Engineering

1kO 3V D2 vs 3kN. Vout D1 6V +

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

What is CEMF?
a) Use the diode’s characteristic equation,ID=Is exp(VD/VT), to determine the currentsourceIso that the output voltage is 1.5 V. b) If a load is attached to the output that draws 1 mA, what is the output voltage? c) If the circuit heats up to 40◦C, what is the output voltage without a load?
Derive the current equations for the circuit shown below, using the labels as shown.Note that rz here is a model of the parasitic imperfection of the Zener diode.a) IL = ?b) II = ?c) IZ = ?d) What impact does rz have on VL?
The circuit shown below is to be used to provide a stabilised output to the load. The Zener diode characteristic is also shown on the next page. Find the load voltage (VL) and source current (IS) if the battery voltage is 18 V, series resistance is 1.4 KΩ and load resistance is 11 KΩ. Additionally, determine the value of the source resistance (R) if the Zener diode is at the threshold of activating in its reverse bias. Comment on the purpose of having this value of R in the circuit.
Describe the operating principle and characteristics of a typical Zener diode found in the market place, including examples of their common applications. The circuit shown below is to be used to provide a stabilised output to the load. The Zener diode characteristic is also shown on the next page. Find the load voltage (VL) and source current (IS) if the battery voltage is 18 V, series resistance is 1.4 KΩ and load resistance is 11 KΩ. Additionally, determine the value of the source resistance (R) if the Zener diode is at the threshold of activating in its reverse bias. Comment on the purpose of having this value of R in the circuit.
diode zener a, DESIGN THE NETWORK IN THE FIGURE, TO KEEP, "VL" at 12 V for a variation in load (IL) from 0 to 200 mA, DETERMINE "Rs" and "Vz" b. determine "P2min" for the Zener diode from section a
For the ideal-diode clipper circuit given below, VS = 12.sinωt V. Determine the output voltage Vout and sketch this function. Remove the short circuit between points x and y, and replace it with a 2kΩ Resistor. Find the range of values of VS for; D1 and D2 are OFF D1 is ON and D2 is OFF D1 is OFF and D2 is ON Is it possible for both D1 and D2 to be ON?
A diode whose internal resistance is 20 ohms is to supply power to a 1000-ohm load from a 110V(rms) source of supply. Calculate the peak load current, dc load current. and determine the percent regulation from no load to the given load. a.) Peak Load Current= 120.8mA; DC load current=25.5mA b.) Peak Load Current= 133.3mA; DC load current=29.4mA c.) Peak Load Current= 144.3mA; DC load current=34.7mA d.) Peak Load Current= 152.5mA; DC load current= 48.5mA
A half wave rectifier circuit with a 1K ohm load operates from a 120V rms 60-Hz household supply through a 10-to-1 step down transformer. It uses a silicon diode that can be modeled to have a 0.7V drop for any current. What is the peak voltage of the rectified output? For what fraction of a cycle does the diode conduct? What is the average output voltage? What is the average current in the load? Thanks for any help.
Draw the circuit diagram of a single phase full-wave uncontrolledrectifier with R-load. Describe its principle of operation. Draw thewaveforms of: input voltage, voltage across the load, current throughthe diodes and their voltage. Write the expressions for: the averageoutput voltage Vd, the maximum reverse voltage across the diode and thestandard transformer power. Describe what the difference will be if acapacitor is added in parallel with the load at the output.
The Single-phase HW Rectifiers with R, L with free while diode find the value of Voltage and Currents (output do and Root Mean Square) with all the proved, then sketch the curve from 0-2 on these axes (vs, VL, VD and it) explain its operation.
Design a voltage-regulator circuit to provide a constant voltage of 5 V to a load from a variable supply voltage. The load current varies from 0 to 100 mA, and the source voltage varies from 8 to 10 V. You may assume that ideal Zener diodes are available. Resistors of any value may be specified. Draw the circuit diagram of your regulator, and specify the value of each component. Also, find the worst case (maximum) power dissipated in each component in your regulator. Try to use good judgment in your design. Repeat Problem P9.29 if the supply voltage ranges from 6 to 10 V.