2- A message signal given by m(t) = 3 cos (400 t+n/2) is sampled with the minimum sampling rate (i.e. Nyquist rate). If the number of levels is 13, compute the following: a. Sampling rate, fs- b. Signal-to-quantization noise ratio (SNR). c. Average quantization power, Pg. d. Number of bits per sample, l. e. Total bit rate, R₂. f. Minimum bandwidth. g. If we record this audio for 7 minutes. What is the file size for this record in bits?

2- A message signal given by m(t) = 3 cos (400 t+n/2) is sampled with the minimum sampling rate (i.e. Nyquist rate). If the number of levels is 13, compute the following: a. Sampling rate, fs- b. Signal-to-quantization noise ratio (SNR). c. Average quantization power, Pg. d. Number of bits per sample, l. e. Total bit rate, R₂. f. Minimum bandwidth. g. If we record this audio for 7 minutes. What is the file size for this record in bits?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A digital data will be transmitted over an analog transmission medium that has amaximum bandwidth of 1.4MHz with SNR=26.2 dB.a) What is the maximum data speed that can be achieved in this system?b) If you consider only the white noise, what is the minimum signal power required withinthis transmission system?c) How many signaling levels should be used to reach to the data rate that you calculated inpart (a)?
2) An analog signal Xa(t) = sin(480pit)+3sin(720pit) is sampled 600 times per second . a) determine the nyquist sampling rate for Xa(t) and the folding frequency ? b)what are the frequencies in radians, in the resulting discrete time signals x(n) ? c)if x(n) is passed through an ideal D/A converter , what is the reconstructed signal Ya(t) ?
Q4. a) Consider a bandlimited message signal of 6kHz bandwidth. It is sampled at the rate of 55% higher than the Nyquist rate. The maximum quantization error of the sample amplitude is 0.5% of the peak amplitude? . Assume binary encoding. Calculate the minimum bandwidth ? of the channel to transmit the encoded binary signal.
1. Consider a continous time signal given below. The signal is digitized and carried via the link operating at the rate of 20 Kbits/sec, and each input sample is quantized into 2048 different voltage levels. x(t) = 2cos(2pi50t) + cos(2pi150t) + sin(2pi35t) a. What is the sampling frequency of the given acquisition? b. Is the sampling frequency sufficient for the given signal to avoid aliasing? If not, what are the aliased frequencies going to be? and from which original frequencies would they come from? c. Assume a bipolar 10-V A/D. What is the resulting quantizer resolution? d. What is the SNRdb of the aquired signal? PLEASE SHOW WORK I really appreciate it Thank you
In a baseband digital communication system, communication is made with pole coding at -1 V and +5 V levels. There is a noise sign of ? ~ ? (0.1) in the channel. It is also given the information that (? = 0) = 0.4. In this case, find the decision threshold that will give the buyer the lowest probability of error. Calculate the total error probability of the system for this decision threshold.
Eight input signals, each of bandwidth 4 kHz are timely multiplexed, quantized and binary PCM coded. The error in amplitude level of quantization process must be greater that 0.00001 of squared of peak amplitude. Find the values of M, N and bit rate if the sampling rate considered as 50% above the Nyquist rate. * 1 M=183 levels, N=8 bits, rb= 768 kbps 2 M=122 levels, N=7 bits, rb= 768 kbps 3 M=222 levels, N=8 bits, rb= 1068 kbps 4 M=162 levels, N=6 bits, rb= 468 kbps 5 M=192 levels, N=8 bits, rb= 868 kbps 6 M=102 levels, N=7 bits, rb= 868 kbps 7 M=202 levels, N=8 bits, rb= 968 kbps
Consider a speech signal with spectral components limited to the frequency band 200 to 3500 Hz. Assume that the sampling rate of 12000 samples/s will be used to generate a PCM signal. The ratio of peak signal power to average quantization noise power (?) ?? needs to be minimum of 40 dB. i) What is the minimum number of uniform quantization levels needed? ii) What is the minimum number of bits required per sample? at the output iii) Calculate the bandwidth of this system required for the detection of such PCM signal.
6.1 A 1 kHz sine wave is sampled at frequency of 5 kHz.(a) What is the Nyquist frequency of the sampling system in this case? Showyour work.(b) What is the Nyquist rate of the signal? Show your work.(c) Is the signal properly sampled; that is, will there be aliases in the digitallyrecorded signal? Explain.(d) What if the original analog signal included both even and odd harmonics of itsprimary frequency; that is, 2, 3, 5 kHz, etc. What would be the highest harmonicthat will be faithfully represented in the discrete-time version of the analogsignal?(e) Following on with the previous step, what is the lowest harmonic that will bealiased and what would be resulting alias frequency?
We need to send data 15bits at a time at a bit rate of 9Mbps. The carrier frequency is 18MHz.Calculate the number of levels (different frequencies), the baud rate, and the bandwidth.
b. Problem Solving: Consider the old landline telephone communication system with a bandwidth ranging from 300Hz to 3,400Hz. The telephone system is generally assumed that to require a SNR of at least 3162 to operate without unacceptable bit errors. Calculate the maximum channel transmission capacity C as predicted by the Shannon equation. Hint: Telephone system signal is ANALOG Calculate the Nyquist data rate given the same bandwidth as in Problem 1 above and assume 8 signal levels per symbol.
1. Given the bit pattern 01010111, encode this data using ASK, FSK, and PSK (i.e., draw the waveform that represents each ‘1’ and ‘0’). In the diagram, label amplitude values used in ASK, frequency values used in BFSK (Binary FSK because there are only 0s and 1s in data), and phase values used in BPSK (Binary PSK). Encode the same data using QPSK.
Solve the following, if a television signal (video and audio) has a bandwidth of 4.5 MHz. This signal is sampled, quantized, and binary coded to obtain a PCM signal.I. Find the sampling rate if the signal is to be sampled at a rate of 20% above the Nyquist rateII. If the samples are quantized into 2048 levels, determine the number of binary pulses required to encode each sampleIll. Determine the binary pulse rate (bits per second) of the binary-coded signal, (or ) the minimum bandwidth required to transmit this signallV. Find the channel capacity using the Nyquist rule.