An AC voltage source has an output of v = (220 V) sin 2 T It and connected to a 70 resistor as shown in the figure. Therefore, the maximum current (Imax) in the circuit and the average power delivered to the circuit would be 1. 3.14 A. 346 W 2. 3.14 A. 249 W 3. 2.22 A, 346 W 4. 2.22 A. 690 W

An AC voltage source has an output of v = (220 V) sin 2 T It and connected to a 70 resistor as shown in the figure. Therefore, the maximum current (Imax) in the circuit and the average power delivered to the circuit would be 1. 3.14 A. 346 W 2. 3.14 A. 249 W 3. 2.22 A, 346 W 4. 2.22 A. 690 W

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.22P: The real power delivered by a source to two impedances, Z1=4+j5 and Z2=10 connected in parallel, is...

See similar textbooks

Related questions

Q: If the inertia constant H = 8 MJ/MVA for a 50 MVA generator, the stored energy is?

A: Given, Inertia constant, H = 8 MJMVA MVA rating, S = 50 MVA

Q: A- Calculate the excitation field current of the synchronous turbo generato needed to get a Vrated…

A: Short Circuit Ratio: SCR or Short circuit Ratio is defined as the field current necessary to…

Q: When 7A current is flowing in electric circuit then the electric potential difference between B B…

Q: In a load flow problem solved by Newton-Raphson method with polar coordinates, the size of the…

A: Given in a load flow analysis of the newton raphson method where Size of the Jacobian matrix =…

Q: D1 RL Vdd = +6 V Lund VF VL Figure 1-2.b 6000 6000

A: If the diode is open then we take the node voltages of that two open nodes to calculate the voltage…

Q: (c) A solar farm contains 300 modules each with an active area of 1 m² and generates 30 kW of power.…

A: Utilization factor:The utilization factor is also known as the use factor where the time used by…

Q: Solve the following questions regarding the BJT transistor circuit shown below What is lg in HA?…

A: Given, A BJT transistor

Q: osition b. ) -) Calculate Vo for t > 0+. What percentage of the initial energy stored in the…

A: Solution- from the above figure, Switch is at position a for t < 0, for the steady state at t =…

Q: SOLVE Vo in the circuit using superposition theoren

Q: A 2-pole, 50 Hz, 11 kV 100 MW alternator has a moment of inertia of 10,000 kg.m². The value of…

A: Given, An alternator has Number of pole, P = 2 Frequency, f = 50 Hz Power rating, S = 100 MW Moment…

Q: How do you get the value of Vab and Vac here? (YELLOW HIGHLIGHTED PART)

A: Given: A balanced 3-phase voltage source Van=200∠0°

Q: (4) Consider an FM signal given by the expression f(t) = cos[2nfet + ß₁ sin(2πf₁t) + B₂ sin(27f₂t)].…

A: Frequency modulation :- It is a technique that encodes information on particular signal by changing…

Q: What is bode plot ?

A: It is the Frequency domain Analysis which consists of Both magnitude Plot and Phase plot. Purpose of…

Q: Given the difference equation a. with x(n)= b. C. y(n + 2)-y(n+1)->(n)= x(n), -(()*. 0, n20 nz0 and…

Q: * E B A F Find any Hamiltonian circuit on the graph above. Give your answer as a list of vertices,…

Q: to c correct the errors that can occur when the data is moved or stored from t to the receiver.…

A: (i) The number of message bit(m) is 16. To find parity bits(p) we use the formula as Given m=16,…

Q: The value le for a transistor where lg is 50 μA and Ic is 3.65 mA is 3.7 mA O 3.6 MA 3 mA O2.9 mA

A: Given, In a transistor, Base current, IB=50 μA Collector current, IC=3.65 mA

Q: A 10 Q2 resistor is connected in series to a parallel combination of a 60 resistor and a 20 resistor…

A: Given data, R1=10ohm R2=60ohm R3=20ohm V=220V

Q: the resistance

Q: 1. For the circuit shown in Figure 5.56, use superposition to find v

Q: 1. Find and draw the Fourier Transform of the signal shown if figure below: f(t) -T coswot T

A: 1) To find the Fourier transform and sketch it Given signal f(t) = cos(wot)

Q: 1 5v T Voltage Voltage 2 V Resistor 1: 47-2 Resistor 2 = 68 Resistor 3 = 39 Current I = ? Current 2…

Q: What is tungsten,CFL,led bulb... Which one save electricity and why ?

A: Please find your answer below.

Q: A potential barrier is 5.00 eV high and 0.900 nm wide. Find the probability that an electron will…

A: The probability that an electron will tunnel through the barrier is given by the expression as shown…

Q: Please use laplace/admittance method in solving the problem

Q: 19 Three parallel loads drawing 3 kW, 5kVA at 0.866 PF lagging and 4 kVA at 0.707 PF lagging are…

Q: The message signal m(t) as shown in the figure is applied to a phase modulator (with kp as the phase…

A: Given similar carrier frequency is used in both FM and PM modulation Instantaneous phase in PM…

Q: 1. Find the Thevenin equivalent (VTH and RTH) between terminals A and B of the circuit given below.…

A: Given data,

Q: Vin = 10 V 4k Ohm O a. 4k Ohm www 3.75 mA Ob. 2.5 mA O c.-1.25 mA O d. 5.7 MA h. 4k Ohm The current…

A: For the given op-amp circuit calculation of current iL. By the virtual short condition: VA=VBThen…

Q: A platinum RTD PT100 measures 100 Q at 0 °C and 139.1 Q at 100 °C. Calculate temperature in °C if…

Q: What are the working principle of air blast circuit breaker

Q: (1) Find the Fourier transform of the signal shown in figure below. f(t) cos (5t)

Q: (b) at the edge of saturation (c) deep in saturation with forced = 10 For simplicity, assume that…

Q: (1) Find the Fourier transform of the signal shown in figure below. f(t) cos (5t)

A: Given figure,

Q: 1. Find the values of I and V in the circuit shown below for the following cases: (i) Assuming the…

A: As per our guidelines we are supposed to be the first three questions only. Kindly repost the other…

Q: d) Describe the construction, principle of operation and application of i) Rod gaps ii) Expulsion…

A: Given types of arresters: Rod gaps Expulsion gap Valve type lightning arrester

Q: Fig. 39.17 shows the negative voltage feedback amplifier. What is the value of feedback fraction?…

Q: -/ 1 Question 10 of 25 View Policies Current Attempt in Progress A square wire loop with 2.3 m…

A: Given data : The magnetic field B=0.035-0.84t The battery EMF E=16V Length of square L=2.3m

Q: A plane wave in air with an electric field amplitude of 2 V/m is incident normally upon the surface…

A: given here a plane wave in air with an electric field amplitude of 2 V/m is incident normally upon…

Q: (c) A solar farm contains 300 modules each with an active area of 1 m² and generates 30 kW of power.…

A: Utilization factor: Utilization factor is also known as the use factor where the time used by…

Q: β=150 VA=∞ R1=60kΩ y R2=40kΩ, RE=0.5kΩ,RC=4kΩ,RL=10k, VCC=15v A) determinar ICQ y VECQ B) determinar…

A: The given circuit is as shown below,

Q: For a 20 KVA, 480/220 V, 60 Hz, single phase transformer. Calculate the phasor load current if the…

A: Given, A single phase transformer with, S=20 KVAV1V2=480220f=60 HzPL=12.6 kWcosϕ=0.881 laggingVL=220…

Q: What Is polar plot? Draw the polar plot considering a unity feedback system with open loop transfer…

Q: A transformer rated at a maximum of 25kVA supplies a 12kW load at power factor 0.60 lagging. a) What…

A: Transformer :- It transfers electric energy and changes voltage through the principle of…

Q: A 50 MVA, 11 kV, 3-phase generator has a stored energy of 400 MJ. Its inertia constant is?

A: Given a 3-phase generator with, MVA rating, S = 50 MVA Stored kinetic energy, K.E. = 400 MJ

Q: 10.36 Compute V, in the circuit of Fig. 10.81 using mesh analysis. ML 4/90° A j4Ω m 2 Ω www 2Ω V₂…

A: Given figure,

Q: A data stream of 60 Mbps is to be transmitted through a wireless channel using 64-QAM technique.…

A: Given, A data stream of, Rb=60 Mbps Transmitted through a wireless channel using, M = 64 - QAM

Q: Problem 15. A source of e.m.f. of 15 V supplies a current of 2A for six minutes. How much energy is…

A: In this question we will find energy provided by source ...

Q: The correct answer for this problem is the following: (a) -8e-10t (b) 80% Can somebody show me…

A: a) To find the output voltage Vo(t) , t > 0 b) To find the percentage of the initial energy…

Q: A transformer rated at a maximum of 25kVA supplies a 12kW load at power factor 0.60 lagging. a) What…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Question

An AC voltage source has an output of v = (220 V) sin 2
T
It and connected to a 70
resistor as shown in the figure. Therefore, the maximum current (Imax) in the circuit and the average
power delivered to the circuit would be
1. 3.14 A. 346 W
2. 3.14 A. 249 W
3. 2.22 A, 346 W
4. 2.22 A. 690 W

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A voltage source V(t) = 10sqr(2)cos(377t + 90) is connected to a load, which is the parallel combination of an R = 5 ohm and XL = 10 ohm. What are the P and Q consumed in the load?
A single-phase consumer who lives in San Francisco has an annual average monthly consumption of 430 kWh. In San Francisco, the average hours of full sun is 3.96 hours / day. Considering the losses of 20%, based on the data below (image), find: The number of photovoltaic panels that will be used.
The amplitude of the voltage available in the 60-Hz, 230-V power outlet in your home is what? A. 250 V B. 300 V C. 325 V D. 350 V
A current source of i(t) = 10 sin(377t + 30◦) A is applied to a single-element load. The resulting voltage across the element is v(t) = −65 cos(377t + 120◦) V. What type of element is this? Calculate its value.
A single-phase consumer who lives in San Francisco has an annual average monthly consumption of 430 kWh. In San Francisco, the average hours of full sun is 3.96 hours / day. Considering the losses of 20%, based on the data below (image), find: The arrangement of these 14 photovoltaic panels that will be used.
A 55000 kW thermal plant of National Power Corporation delivers an annual output of 238000000 kw-hr with a peak load of 44 MW. What is the capacity factor? a. 49.4% b. 42.4 % c. 48.2% d. 44.6%The Answer is not 63.74.
"A residential house has a lighting load of 1000W and a small appliance load of 2000W. If they are used at the same time, what will be the monthly bill at an energy cost of P 0.40 per kWh?"
An industrial assembly hall is continuously lightedby one hundred 40-W mercury vapor lamps suppliedby a 120-V and 60-Hz source with a power factor of0.65. Due to the low power factor, a 25 percent penaltyis applied at billing. If the average price of 1 kWh is$0.01 and the capacitor’s average price is $50 permillifarad, compute after how many days of operationthe penalty billing covers the price of the power factorcorrection capacitor. (To avoid penalty, the powerfactor must be greater than 0.85.)
Problem : In the case of an industrial load with a power factor of 0.707 lagging, consuming 100 kW, and the line voltage at 60 Hz is 480Vrms, with a line resistance of 0.1Ω between the power company's transformer and the load, calculate the amount of power saved if the load's power factor changes to 0.94 leading. The answer is "3.771 Kilo-Watt has been saved" and also I want to know the concept of 'Power Factor'.
Q4. The source current in the circuit shown is in Figure 3a) What impedance should be connected across terminals a,b for maximum average powertransfer?b) What is the average power transferred to the impedance in (a)?c) Assume that the load is restricted to pure resistance. What size resistor connected across a,bwill result in the maximum average power transferred?d) What is the average power transferred to the resistor in (c)?v
If the voltage in a European Outlet is 220V rms, what is the Vp-p of that value? A) 120 Vp-p Hz B) 155.6 Vp-p C) 311 Vp-p D) 622 Vp-p
Find the average power delivered by the ideal current source in the circuit if ig=40cos 1250t mA.