2- Compare the weight of equal lengths of hollow and solid shafts to transmit a torque T for the same maximum shear stress. For hollow shaft, the inner and outer diameters have relationship D; = 2/3 D. = 2/3 Diollow-

2- Compare the weight of equal lengths of hollow and solid shafts to transmit a torque T for the same maximum shear stress. For hollow shaft, the inner and outer diameters have relationship D; = 2/3 D. = 2/3 Diollow-

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.11P: ‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses...

See similar textbooks

Related questions

Q: In an industrial machine, two shafts have to be connected by using a muff coupling. The shaft…

Q: 3.31 A hollow steel shaft, 6 ft long, has an outer diameter of 3 in. and an i diameter of 1.5 in.…

Q: A hollow bronze shaft (G=5000ksi) has an outer diameter of 3in and a wall thickness of 0.25in. The…

A: Given data: Converting all data into SI units. Modulus of rigidity G=5000 ksi=34473.8 Mpa Outer…

Q: 3.33 The figure shows an inboard engine, 8-fN long steel drive shaft, and propeller for a motor…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: 3.13 The torques T and 2T are carried by a shaft consisting of steel and aluminum segments. If the…

A: Given:ζs=14,000 psiζa=7,500 psiθmax=8Gs=12*106 psiGa=4*106 psi

Q: d Bronze B Steel - b–

Q: 3.13 The shaft consisting of steel and aluminum segments carries the torques T and 27. Find the…

Q: A line shaft rotating at 320 rpm is to transmit 35 kW power. The allowable shear stress for the…

A: Given Data⇒ Line shaft rotating at (N)=320 rpm Power transmitted (P)=35 KW Allowable shear stress…

Q: 4. A steel shaft 4 ft long that has a diameter of 5 in is subjected to a torque of 20 kip-ft. Use a…

Q: Two steel shafts (G=77.2 GPa) are connected to a coupling disk Band to fixed supports at A and C.…

A: Both the shafts AB and BC are connected in parallel, therefore the angle of twist is the same in…

Q: Question 4. The shaft is made from a solid steel section AB and a tubular portion made of steel and…

A: Given data: T=50 kN.m Need to determine the angle of twist, at point C, maximum shear stress,…

Q: Q.1: Calculate the maximum shear stress developed in each segment when the torque T = 100 N.m. is…

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

Q: A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 MPa. It is further…

A: Data given- d = 100 mm σaxial = 50 MPa T = 10 kN-m

Q: 4- A 4m long solid circular steel shaft is fixed at one end, and subjected to a twisting torque of…

Q: Will cause a shear stress of 6000 psi? 3.41 The constant wall thickness of a steel tube with the…

A: Given Radius, R = 10 mm Diameter, D = 20 mm Torque, T = 600 N. m Length, L = 30 mm Find…

Q: A stepped shaft ACB having a solid circular cross sections with two different diameters and two…

Q: A höllow circular shaft has an external diameter of 120 mm and the internal diameter is…

Q: Q2. A solid circular shaft is subjected to a bending moment of 2500 N-m and a torque of 7 000 N-m.…

A: We will calculate diameter of shaft considering two types of failure: Maximum principal stress…

Q: a hollow shaft for a rotary compressor is to be designed to transmit maximum torque of 4750 n-m. the…

A: Given Data⇒ Hollow shaft Maximum torque : Tmax=4750 N-m Shear stress in shaft : ζ=50 Mpaζ=50×106Pa…

Q: : Q2 /A hollow steel shaft transmits 200 kw of power at 150 rpm .The total angle of twist in length…

Q: Task 3: A hollow aluminum alloy 6061-T6 shaft of outer radius c = 40 mm, inner radius b = 30 mm, and…

A: Given data:

Q: In an industrial machine, two shafts have to be connected by using a muff coupling. The shaft…

A: Given,

Q: Q1: A motor driving a solid circular steel shaft transmits 30 kW to a gear at B (as shown). The…

A: Given:P=30 KWζ=40 MPa

Q: A hollow circular shaft transmits 25 horsepower while operating at a rate of 180 rev/min. If the…

Q: ropeller shaft of diameter 30mm. If the llowable shear stress of the shaft and oupling material is…

Q: 3.30 A solid steel shaft transmits 20 hp while running at 120 rev/min. Find the smallest safe…

Q: Q3/A solid circular shaft is subjected to a bending moment of 3000 N.m and a torque of 10000 N.m.…

Q: An aluminium hollow thin-wall torsion member shown in Fig. 3.15 is 3 m long. If a torque of 10 kN-m…

A: We know that a 3 m long aluminium hollow thin wall torison member is illustrated in the diagram.We…

Q: A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 MPa. It is further…

A: Given, Diameter of shaft = d = 100 mm Axial stress = σa = 50 MPa Torque = T = 10 kNm = 10 x 106 Nmm…

Q: Q4-A circular shaft consists of steel and aluminum segments is subjected to the torques shown in…

Q: 1 of 1 -1.5m- Q: Aluminum shaft of 30mm diameter and 1.5m lenght is subjected to a torque of 500N.m…

Q: Q2 /A hollow steel shaft transmits 200 kw of power at 150 rpm .The total angle of twist in length of…

Q: 1) A solid steel drive shaft is required to transmit 12 hp. The allowable shear stress for steel is…

Q: If the internal torque experienced by a hollow brass shaft (G = 39 GPa) at a section with diameter d…

Q: A composite shaft is made of slipping a bronze tube of 3-in. outer diameter and 2-in. inner diameter…

A: Calculate the polar moment of inertia of the solid steel shaft-Jst=π32D4Where-D=diameter of steelD=2…

Q: Task 4: A solid steel shaft in a rolling mill transmits 20 KW of power at 2 Hz. Determine the…

A: The steel shaft of the rolling mill transmits 20KW at 2 Hz, The torque in the shaft while…

Q: connected by using a muff coupling. The shaft rotates at a speed of 620 rpm and transmits a power of…

Q: A SOLID circular shaft transmits 50 horsepower while operating at a rate of 150 rev/min. If the…

Q: 1. A shaft 80 mm diameter transmits power at maximum shear stress of 63 MPa. Find the length of a 20…

A: Given data diameter of shaft (d) = 80 mm maximum shear stress in shaft (τmax) = 63 MPa width of…

Q: A shaft 80 mm diameter transmits the power at maximum shear stress of 63MPa. Find the length of a…

A: Given details: d=80 mmζmax=63 MPawkey=20 mmζkey=42 MPa Formula used:…

Q: T 100 mm 70 mm 70 mm 1.5 m 2 m T

Q: The halves of the coupling are held together by four 5/8-in.-diameter bolts. The working stresses…

Q: A flange-and-bolt coupling between two shafts carries 12 bolts at a pitch diameter of 18 in. The…

A: Given data: In a Flange and Bolt coupling between two shafts: Number of bolts, n=12. Pitch circle…

Q: The shaft consisting of steel and aluminum segments carries the torques T and 3T. Find the largest…

Q: The solid and hollow shafts are each subjected to the torque T. In each case, sketch the shear…

A: The solid shaft is subjected to torque T in a clockwise direction. The shear stress is calculated…

Q: II. A stepped shaft ACB having a solid circular cross sections with two different diameters and two…

A: Given LA= 225 mm ; diameter of circular cross section A (dA)= 20 mm ;And LB= 450 mm ; diameter of…

Q: -1.5m Q: Aluminum shaft of 30mm diameter and 1.5m lenght is subjected to a torque of 500N.m as in…

Q: A shaft is 21/2 in. square, and the allowable shearing unit stress for the material is 6000 psi. The…

Question

2- Compare the weight of equal lengths of hollow and solid shafts to transmit a
torque T for the same maximum shear stress. For hollow shaft, the inner and outer
diameters have relationship D; = 2/3 D, = 2/3 Diollow-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
Solve the preceding problem for a column with e = 0.20 in,, L = 12 ft, I = 2L7in4, and E = 30 × 106psi.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?