2) For the wye-connected load of Fig. below, the line voltages all have a magnitude of 250 V and are in apositive phase sequence. Calculate the line currents and the neutral current. 40/60° 2 60/-45° 2 20/0°2 In

2) For the wye-connected load of Fig. below, the line voltages all have a magnitude of 250 V and are in apositive phase sequence. Calculate the line currents and the neutral current. 40/60° 2 60/-45° 2 20/0°2 In

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.24MCQ: Consider a three-phase Y-connected source feeding a balanced- load. The phasor sum of the line...

See similar textbooks

Related questions

Q: Compare the results of static or dc resistance of the diodes obtained from different values of rever...

A: The characteristics of a virtual diode and a 1N4001 diode is shown in the question. The values of re...

Q: The instantaneous values of two alternating currents are given by i, = 20 sin wt and i, = 10 sin (wt...

A: The solution is given below

Q: 2. A standard vapor compression system produces 25 Tons of Refrigeration using R 12 as refrigerant w...

A: Vapour Compression Refrigeration Cycle- In VCR Systems like house refrigerators ,the compressor us...

Q: The position of a particle moving along the x-axis is given by (X(t)=3t+2t^3 ). Find the acceleratio...

A: Given,The position of a particle moving along x-axis is,X(t) = 3t+2t3 Here, we have to determine the...

Q: 10- Find current in 3 ohm resistance by Thevenin's Theorem then by mesh theorem -30 V 5 A 30 20 20 2...

A: The given circuit is given as,

Q: calculate the magnitude of the voltage drop across the jik ohm inductor 1.2 k2 jl k2 -j4.7 kQ j2.2 k...

Q: #7.7 An amplifier has a voltage transfer function 10° s T(s) = (s+10)(s+1000) Convert this to the fo...

Q: what are the electrical, electronic, and robotic components of the robotic circuit?

A: Robotics is the science and technology that underpins the creation, manufacture, and use of robots. ...

Q: For the P-only control , briefly explain changes in controller gain and offset (steady-state error) ...

A: In this question we will write effect of change in Proportional band on proportional controller gai...

Q: 20 52 10.4: For the circuit shown: 1. Find the Z-Parameters? 2. Find the Y-Parameters? ww 20M Eng 50...

Q: 4. Compute the power dissipated by a. A 5-ohm resistor with 5-A current b. A 12-V battery with 12-A ...

A: The solution is given below

Q: 2. A parallel circuit has 3 resistors each on different paths connected to a 120 V potential differe...

Q: (use Loug division) 2x'-3x*+リメ+5 X+ 2

Q: The circuit given below is for a difference amplifier. Find vo given that n = 1.8 V and v2 = 2.4 V 3...

A: In this question we will find output colgate of opamp....

Q: Problem: Obtain the unit-step response of a unity-feedback system whose open loop transfer fune: tio...

A: Given data, Unity feedback system with Open loop transfer function, Gs=s-2s2

Q: 32. (a) A series connection is formed between a 1 2 resistor, a 1 F capacitor, and a 1 H inductor, i...

Q: 2- Explain the effect of increasing the filter capacitance on the output voltage.

A: 2. When the capacitor size is increased then the peak current in the diode and the dc voltage will a...

Q: The resistance of a coil of copper wire is 3.35 2 at 0°C. What is its resistance at 50°C. For copper...

A: GivenTemperature T1=0°CResistance at 0°C=3.35ΩT2=50°CTemperature coefficent α=4.3×10-3C-1

Q: What are the advantages of an open-loop control system?

A: 1)Open loop control system simple in construction doesn't need much components like closed loop cont...

Q: State Cayley Hamilton theorem and discuss how it can be used to find the State Transition matrix.

A: The solution is given below

Q: P.8 – A slip ring type three-phase asynchronous motor, 50HZ, 4 magnetic poles, 380V, has the followi...

A: It is given that: f=50 HzP=4V=380Vrs=0.3 ΩrR=0.2 Ωm=0.5Xm=0.8 ΩAssuming,Xr=Xs=Xm=0.8Ω

Q: Main winding: R = 10 Q, L, = 63,7 mH I R1 L1 C2 R2 Auxiliarly winding: R2 = 10 N, L, = 63,7 mH, C2 =...

A: The Solution is given below

Q: A short shunt compound generator has an armature,shunt field and series field resistances of 0.02 oh...

Q: 4. Construct a complex circuit that will produce a total resistance of 9540.54 Draw your diagram. Us...

Q: A long wire carrying a certain current produces a magnetic field of 0.8 Tesla at a distance 0.5 cm. ...

Q: An ac voltage of peak value 20v is connected in series with a silicon diode and load resistance of 5...

Q: 3.- Express the following terms in their polar form. a) -18.5-j26.1 b) 17.9-j12.2 c) -21.6+j31.2.

A: (a) -18.5-j26.1=-18.52+-26.12tan-1-26.1-18.5=31.99∠54.670

Q: The armature of a 4-pole lap wound dc motor has 850 conductors and draws an armature current of 70A ...

Q: Question 2 Consider the closed-loop system shown in in Fig. 2. G:(3) U(s) Process G(5) 15 3+ 5s + 11...

A: Given, Closed loop system:

Q: (a) Calculate the ratio of the polar optical phonon emission rate to the absorption rate for AIAS at...

A: It is given that: Temperature=300 KPhonon energy in =50 mEV=0.05 eVElectron energy=35 meV=0.0.035 eV

Q: Consider an FM signal s(t)=10 cos(2n 10 t+8 sin 4n 10 t).Determine a. modulation index b. frequency ...

Q: 1. Fill in the table for this circuit. 14 V R R. R, Total V ER R3 3.3 kN I 780 2 R R 780 2 1.5 k2 3....

Q: The base impedance and base voltage for a given power system are 10Ω and 400V, respectively. Calcula...

Q: Hydrogen atoms in states of high quantum number have been created in a lab. (a) Find the quantum num...

A: (a) The radius of the nth orbit of the hydrogen atom is given as: rn=0.529n2 Ao Plugging the known ...

Q: Find i, (using superposition theorem) i, = 0.1 + 0.22 cos(2000t + 134.1°) – 1.37sin(4000 + 14.21°)A ...

A: Provided answer is incorrect . I have checked the solution . This question belongs to circuit theory...

Q: 3) a) What is the logic function that is implemented by the gate in the below figure? b) What are th...

Q: 52 10.4: For the circuit shown: 1. Find the Z-Parameters? 2. Find the Y-Parameters? 202 V1 20 V2 ng ...

Q: Ps: The differente equation of the Rillowing. dingram. is 3. -4

A: Block deduction- In control system, the whole system is represented in block form which are deduced ...

Q: R1 RL R4 330 1.5k 330 Vs R2 R3 R5 470 470 1k. 5V .tran 10ms

A: Circuit diagram is given as,

Q: A 10mF capacitor has the current waveform as shown. Assuming that v(0) = 7V, sketch the voltage wave...

A: The solution is given below

Q: The voltage across three component in a series circuit when connected across an AC supply are 30 sin...

A: Brief description : Let us consider a sinusoidal signal V(t) = Vm sin(wt + Φ) Volt Vm : Peak Value...

Q: How many digital pins are there in the UNO board? [LO: ARD] 16 20 14 12

A: An Arduino UNO board is shown below,

Q: 15. For the network of Fig. 9.80: a. Determine re- b. Find Ay = Vo/Vi- c. Calculate Zi.

Q: #2) What is He power generated by the source in the circuit and Vs Pes SK R6 6K. Rz 181 Vs R3 12K 4K...

Q: #8)- FIND VO of Vo

A: For the given circuit we have to find the value of voltage vo

Q: #5) Compute all the voituges and cuwats in this cireuit: I5 Ve 3KR Va +, 24V Iz Is

Q: What is the circuit time constant? 1 kQ i(1) I mH ll

A: For RL series circuit time constant =Inductance/resistance I.e. time constant = L/R.

Q: a 3 IV it, 9.

A: The solution is given below

Q: 5. Sketch Vo for the following circuit. 12 V + 0.1 pF R2 56 ka 2V -12 V 1-1 kHz

Q: 10s T(s) = (1 + 703)(1 + 706) Provide your Bode plots for: i) magnitude and ii) ii) phase response a...

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

2) For the wye-connected load of Fig. below, the line voltages all have a magnitude of 250 V and
are in apositive phase sequence. Calculate the line currents and the neutral current.
40/60° 2
60/-45° N
20/0° N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the current Ica in a balanced delta load of j12 ohms, if it is connected to a node of a balanced three-phase network where Van= 120<30° Vrms.
2. A balanced three-phase source furnishes power to the following three loads: Load 1: 8 kVA at 0.83 pf lagging Load 2: unknown Load 3: 10 kVA at 0.7071 pf leading If the line current is 72 Arms, the line voltage at the load is 221 Vrms, and the combined load has a 0.8 pf lagging, determine the unknown load.
Three identical impedances of 10∠ − 15° Ω to a line voltage of 208 V in star connectedconnected to a balanced source. We accept all line and phase voltages and currents as Vca as reference.Calculate in the form (Assume positive order).
Determine the line current of a Y-connected balanced three-phase load, consuming 300 kW at power factor = 0.8 lagging and operating at 480 V. Work on PER UNIT with Sbase = 375 kVA and Vbase = 480V. Choose the best answer.
30. A 30-Y-connected load is connected between three line terminals, R, Y, B, the impedances (in ohms) of the load being: (I + 2) between R and the star point. (2+3) between Y and the star point and (3+j4) between B and the star point. The phase sequence is RYB. If the line voltage is 400 V, calculate the voltage between R and the star point. [181 V]
In a balanced three phase system, load 1 draws 60 kW and 80 leading kVAr whereas load 2 draws 160 kW and 120 lagging kVAr. If line voltage supply is 1 kV, find the line current supplied by the generator. Both loads are 3-∅ loads.Single line text.
A balanced delta-connected load has phase impedances of 4+j3 Ohms. It is connected to balanced transmission lines, with Vab = 1.5kV @ 15 degrees. a) What is the current through each of the load phases? b) What is the current through each of the transmission lines? c) Which ACSR cable should be used for these transmission lines to give a 20% current rating margin for this load?
The current ICA in a balanced three-phase Δ-connected load is 8 −15° A. If the phase sequence is positive, what is the value of IcC?
A wye-connected unbalanced load, Za = 10 angle 36.9 , Zb = 10 angle -36.9 , and Zc = 10 angle 0 are connected across a balanced 130-V, 3-phase system. Determine the reading of two wattmeters with line c as common.
A balanced star-connected load having an impedance (15+j20) ohms per phase is connected to a three-phase, 440 V, 50 Hz supply. Find the line currents and the power absorbed by the load. Assume negative phase sequence.
Determine the amplitude of the line current in a three-phase system with a line voltage of 207 V that supplies 828 W to Δ-connected load at a lagging PF of 0.55, then find the phase impedance.
NOTE: YOU MUST USE THE STANDARD PHASE DIAGRAMTO A THREE-PHASE SYSTEM WITH LINE VOLTAGE OF 230 VAC 60 HZ, A BALANCED LOAD OF 9+j6 Ω IS CONNECTED.IF THE LOAD IS CONNECTED IN DELTA, DETERMINE:A) THE MAGNITUDE OF THE CURRENT OF Ia.B) THE ANGLE OF THE LINE CURRENT Ia.C) THE THREE-PHASE POWER CONSUMEDD) THE VALUE OF EACH CAPACITOR (IN μF) OF THE STAR-CONNECTED CAPACITOR BANK, TO CORRECT THE PF TO ONE.