(2) It is desired to deliver 60 m'/hr of water at 20°C through horizontal asphalted cast iron pipe. Estimate the pipe diameter d that will cause the pressure drop to be exactly 40 kPa per 100 m of pipe length. Take water density p Solve this problem iteratively using either Moody chart or the Colebrook equation. = 998 kg/m² and dynamic viscosity µ = 0.001 kg/(m.s).

(2) It is desired to deliver 60 m'/hr of water at 20°C through horizontal asphalted cast iron pipe. Estimate the pipe diameter d that will cause the pressure drop to be exactly 40 kPa per 100 m of pipe length. Take water density p Solve this problem iteratively using either Moody chart or the Colebrook equation. = 998 kg/m² and dynamic viscosity µ = 0.001 kg/(m.s).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

liquid (density 800kg/m3, viscosity 10−3 kg/ms) has to be supplied at a mean speed of 2m/s through a pipe of diameter 12.5mm with a surface roughness equivalent to that for structural steel. What is the magnitude of the pressure gradient necessary to achieve this flow? Your answer should have a positive sign and be to the nearest 10 Pa/m. You may wish to use the Moody diagram.
If a dust-proofing oil at 30°C had been flowing at 0.046 m /s through a 150-mm pipe in which along-radius flow nozzle 75 mm in diameter, what would have been the deflection of the mercury? Assume C=0.98.
A laminar flow element measures low gas-flow rates with a bundle of capillary tubes packed inside a large outer tube. Consider oxygen flowing at 84 ft3/min in a 4-in-diameter pipe. (i) Is the flow approaching the element turbulent? (ii) If there are 1000 capillary tubes, Length L, is 4 in, select a tube diameter to keep Reynold’s number below 1500 and also to keep the tube pressure drop not greater than 0.5 lbf/in2 (iii) Do the tubes selected fit nicely within the approach pipe?
Water flows through a 16-inch pipeline at 6.7 ft3/s. Calculate the Darcy friction factor using Colebrook-White Equation if the absolute pipe roughness, e, is 0.002 in. Then calculate the head loss due to friction in 1000 ft of pipe length. Use the water kinematic viscosity to be 1.2*10-5 ft2/s.
Nitrogen gas under a pressure pn = 15 psig is used for pumping kerosene at 25°C (density = 816 kg/m3, viscosity = 1.81 cP) through an elevation increase of 6 m. If there is an effective length of 45 m of nominal 2-in. schedule No. 40 pipe (commercial steel) between the two tanks, what is the flow rate of kerosene? Neglect exit kinetic-energy effects.
A smooth pipe 30 cm in diameter and 100 m long has a flush entrance and a submerged discharge. The velocity is 3 m/s. If the flowing water has a kinematic viscosity of v=1.16x10^-6 m² /s, What is the total head loss, hL?
Sunflower oil (SG = 0.7, viscosity = 154cP) is pumped at a rate of 85 ft^3/min (ID = 3.5in) from large open reservoir to the bottom of another open tank. The liquid level in the reservoir is maintained at 4.5ft, and the bottoms of the reservoir and tank are 17ft apart, vertically. Friction losses in the pipe amount to 7.5% of the elevation head. If 2 hp of power is required for the process, what is the expected liquid level in the receiving tank?
A pump delivers 1 hp to a water at 68°F flowing in a 10-in-diameter horizontal, cast iron pipe at V = 6.6 ft/s. Estimate the proper pipe length (in feet) that will match these conditions. For water at 68°F: ρ = 1.94 slug/(ft^3), and μ = 2.09E-5 slug/(ft-s). Assume also that the head added by pump matches the head loss. Round your answer to 2 decimal places.
An oil with density of 900 kg/m2 and viscosity of 0.0002 m2/s flows upward through a 10 m long pipe segment inclined at 40℃ with the horizontal. The pressure a the upstream and downstream end of the pipe are 350 kPa and 250 kPa, respectively. The diameter of the pipe is 60 mm. Assume the flow is laminar. What is the head loss along the pipe segment? 3.77 4.9 5.35 6.1 What is the velocity of the fluid flow? 3.37 2.95 2.08 2.7 Which of the following gives the Reynold’s number? 810.9 624.21 1011.15 885.63
A certain garden hose is advertised to be able to deliver 550 gallons of water per hour. If the hose if 50 feet long and has an inside diameter of 5/8 inch, estimate the water pressure necessary to deliver this much water, assuming laminar flow and viscosity at 1.002 x 10-3 kg/(m-s)
Fluid Mechanics Laboratory Experiment No.5 Pitot Static Tube The Discussion 2 — When the pitot tube is moved vertically inside the pipeline, why does it yield different flow velocities? Explain 3 — If the pitot tube is not perfectly aligned with the current direction, it produces errors in the measurements of static pressure and total (pool) pressure, Why? Explain. 4 — When flow velocity increases, it alters the shape of the flow velocity profile. Clarify 5 — What are the advantages and disadvantages of the pitot static tube. 6 — Does altering fluid temperature influences the results obtained by pitot static tube? clarify
An annulus of narrow clearance causes a very largepressure drop and is useful as an accurate measurementof viscosity. If a smooth annulus 1 m longwith a = 50 mm and b = 49 mm carries an oil flow at0.001 m3/s, what is the oil viscosity if the pressuredrop is 250 kPa?