The flanged cantilever steel beam with riveted bracket is subjected to two forces and couple shown, and their effect on the design of the attachment at A must be determined. Replace the two forces and couple b an equivalent couple M and .resultant fore R at A 2 kN 0.5 m 1.5 m 70° t0.15 m JA (0.15 m 500 N-m L--x 4 1.2 kN

The flanged cantilever steel beam with riveted bracket is subjected to two forces and couple shown, and their effect on the design of the attachment at A must be determined. Replace the two forces and couple b an equivalent couple M and .resultant fore R at A 2 kN 0.5 m 1.5 m 70° t0.15 m JA (0.15 m 500 N-m L--x 4 1.2 kN

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.67P: The cable AB supports a uniformly distributed load of 12 lb/ft. Determine the angles A and B, and...

See similar textbooks

Similar questions

A steel rod is acted upon by the loading shown below. 50 mm2is the area of the circular rod. The coupling sizes at B, C, and D are neglected. Use E st = 200 GPa.
Created from steel and brassgraded Rod, two at each endplaced between the fixed wall, B60kN respectively from and D pointsand 40kn axial forceswere exposed. Accordinglysteel (Eçelik=200GPa andEpirus=105GPa) formed in ricemaximum stressescalculate.
The cantilevered W530 x150 beam shown is subjected to a 8.6-kN force F applied by means of a welded plate at A. Determine the equivalent force-couple system at the centroid of the beam cross-section at the cantilever O.
THE TWO MAIN CABLES OF THE AKASHI KAIYO SUSPENSIONBRIDGE IN JAPAN HAVE A SPAN L= 1990m AND A SAG H = 233m.THE LOADING ON EACH CABLE ISWO = 444.7 KN/m (withouttraffic) ALONG THE HORIZONTAL. DETERMINE THE CORRESPONDING MAXIMUM FORCE IN ONE OF THE CABLES. Give: Given, FBD, AND solution
The cable of the suspension bridge spans L=140m with a sag H=20m. The cable supports a uniformly distributed load of w0 N/m along the horizontal. If the maximum allowable force in the cable is 4 MN, determine the largest permissible value of w0.
Determine the unknown forces by applying d’alemberts principle to a free body.
A 5-m long simply supported timber beam carries two concentrated loads as shown. If L = 16 KN and M = 54 kN, determine the magnitude of the vertical force acting at support D.
The uniform 10 kg rod AB is supported by a ball and socket joint at A and by the cord CG that is attached to the midpoint G of the rod. Knowing that the rod leans against a frictionless vertical wall at B and that the tension in the cord CG, TCG=52.1 N, determine the following a.) Which of the following best shows the equivalent force-couple set at point A of the tension at cord CG, TCG? Choices: a F= -36.8 N i + 24.5 N j - 27.6 N k M = -7.36 Nm i - 11.03 Nm j b F= -36.8 N i + 24.5 N j - 27.6 N k M = -7.36 Nm i - 29.4 Nm k c F= 36.8 N i - 24.5 N j + 27.6 N k M = 7.36 Nm i + 11.03 Nm j d F= 36.8 N i - 24.5 N j + 27.6 N k M = 7.36 Nm i + 29.4 Nm k b.) Which of the following moments is equal to zero? Choices: The moment of the tension in cord CG, TCG about point OThe moment of the tension in cord CG, TCG about point AThe moment of the tension in cord CG, TCG about point BThe moment of the tension in cord CG, TCG about axis AB
Determine the resultant load on the most stressed bolt in the eccentrically loaded connections shown, using the elastic method.
The truss has concentrated loads as shown. The wind loads of 25KN are perpendicular to the member AF. Solve for the forces acting on the members BE, DE, DG by the method of joints.
Two beams are connected together by the short link BC. F1 = 15kN, F2 = 25kN. Solve for all supporting reactions at A and D
Determine all of the forces of the members. Method of Henneberg.