2-liter soda bottles do not have flat bottoms. A bottle can be approximated as a cylinder filled from the bottom up to 0.26-m high with a hemispherical space of 10-cm-diameter underneath. If you treat the soda as having the density of water, what is the force in N of the soda on the curved bottom of the soda bottle?

2-liter soda bottles do not have flat bottoms. A bottle can be approximated as a cylinder filled from the bottom up to 0.26-m high with a hemispherical space of 10-cm-diameter underneath. If you treat the soda as having the density of water, what is the force in N of the soda on the curved bottom of the soda bottle?

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 45P

See similar textbooks

Similar questions

An open vessel 4.0m wide, 5.0m long and 3.5m deep contains 3m of water. It is then accelerated to the right along its width. a. Calculate the acceleration just about water to spill. b. At this rate, what is the force (in N) causing the acceleration if the mass of the vessel if the mass of the vessel is 600kg? c. Consider the same vessel accelerated at 7.00 m/s2. Determine the volume (in m3) of water spilled at that acceleration.
A 65 cm cube weighing 2.5KN is lowered in a tank containing 1.50 m of water below 1.20 m of oil of specific gravity 0.82. If the sides of the cube remain vertical: a. How much of the cube projects above the oil-water interface? b. What is the total hydrostatic force acting on the side of the cube?
A solid object having a specific gravity of 3.5 is floating on a liquid having a specific gravity of 13.6. The volume of the object is 0.02 cubic meters. What additional vertical force is required to completely submerge the liquid?
A 150-lb cylindrical tank is at rest as shown. Determine force P in lb required to move the tank up the higher-level surface.
A rectangular car tank 30m long, 4m wide and 3m deep is completely open at the top. If it is initially filled to the top, what is the max force acting on the side opposite to the direction of the acceleration? Unit of the Correct Answer: kN
A block of mass m = 1 kg is released from the top of an inclined plane with a height h = 80 cm and a slope of 37 °. The kinetic friction coefficient between the block and the inclined plane is u = 0.3. Find the value (in J) of the work done by the friction force until the block reaches the bottom of the incline.
Q4 A plate 0.05 mm distant from a fixed plate moves at 1.2 m / s and requires a force of 2.2 N / m² to maintain this speed. Find the viscosity of the fluid between the plates.
A metal block 2 ft square and 10 in. deep is floated on a body of liquid which consists of an 8-in layer of water above a layer of mercury. The block weighs 120 lb/ft3. What is the position of the bottom of the block?If a downward vertical force of 500 lb is applied to the center of this block, what is the new position of the bottom of the block?Assume that the tank containing the fluid is of infinite dimensions.
A concrete dam given in the figure has water 35 m deep acting on its vertical sides. The coefficient of friction between the soil and the dam is 0.60. Yconcrete 23.5. How far in meters is the vertical resultant force from the toe? a-28m b-25m
A rectangular tank 20 ft long by 6 ft deep by 7 ft wide contains 3 ft of water. If the linear acceleration horizontally in the direction of the tank's length is 8.05 ft/sec2, (a) compute the total force due to the water acting on each end of the tank and (b) show that the difference between these forces equals the unbalanced force necessary to accelerate the liquid mass.
An open rectangular tank mounted on a truck is 5m long, 2m wide and 2.5m high is filled with water to a depth of 2m. (a) What is the maximum horizontal acceleration can be imposed on tank without spilling any water and (b) determine the accelerating force on the liquid mass? (c) If the acceleration is increased to 6 m/s2, how much water is spilled out?
A 5 cm diameter horizontal jet of water with a velocity of 30 m/s strikes a flat plate that is moving in the same direction as the jet at a velocity of 10m/s. The water splatters in all directions in the plane of the plate. How much force does the water stream exert on the plate? What is the work done per second and the efficiency?