Answered: A plate 0.05 mm distant from a fixed…

A plate 0.05 mm distant from a fixed plate moves at 1.2 m / s and requires a force of 2.2 N / m² to maintain this speed. Find the viscosity of the fluid between the plates

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 17P

See similar textbooks

Related questions

Q: Q1:A plate (0.005 cm )distance from a fixed plate move at ( 72000 mm/min) and requires a force of…

Q: Show the possible arrangement of fluid position in the following pressure measuring devices under…

A: Case 1 - Piezometer connected to the side of a water tank containing water up to 2 m depth.

Q: -Q.4 MASS FLOW AT A PIPE JUNCTION Consider the steady flow in a water pipe joint shown in the…

Q: A cylindrical tank containing a fluid (sg = 0.75) is accelerated upward by a net force of 40 lb. The…

Q: A cylindrical vessel 15 cm diameter and 40 cm long is completely filled with water. The vessel is…

Q: A closed cylindrical vessel of diameter 15 cm and length 100 cm contains water up to a height of 80…

Q: A cylinder vessel filled with water with a 2m diameter and 5m high. It was rotated with uniform…

Q: Show the possible arrangement of fluid position in the following pressure measuring devices under…

A: Asked: Show the possible arrangement of fluid position in the following pressure measuring…

Q: A vertical cylindrical tank is 9 m high and 5 m in diameter. It is two thirds full of water and is…

Q: The mass of body Ais 45 kg. The coefficient of friction for bodies A, B, and the ramp C is 0.10.…

Q: A U - tube is made up of two capillaries of bores 1.2 m and 2.4 mm respectively. The tube is held…

A: It is required to determine the mass density of liquid. ∆H=2σcosθr2-r1ρg Here ∆H is the difference…

Q: Q3) A tube is used as a siphon to discharge an oil of specific gravity 0.8 from a large open vessel…

A: Solution;

Q: -Q.17 MASS FLOW AT A PIPE JUNCTION Consider the steady flow in a water pipe joint shown in the…

Q: Q8) You are designing a system for moving aluminum cylinders from the ground to a loading dock. You…

Q: Q4) Water flows through a contraction section as shown. A pressure gage connected between the…

Q: A jet of water strikes with a velocity of 26.36 m/s on a flat plate, inclined at 30o with the axis…

A: Velocity v= 26.36m/s Diameter of nozzle =291mm

Q: Fluid having sp. gr. 0.88 enters the cylindrical arrangement shown in Figure 5 10 at section A, at…

A: Given:- The specific gravity of the fluid = 0.88 Fluid enters at section A = 0.16 N/s The diameter…

Q: A small funnel in the shape of a cone is being emptied of fluid at the rate of 15 cubic centimeters…

A: Given values, rate of flow = 15 cubic centimeters per second height of the funnel = 23 cm radius…

Q: A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the %D figure. Determine…

A: Let's unit weight of water (Yw) = 62.4 lb/ft3

Q: A liquid having a sp.gr. of 20 is flowing in a 50 mm diameter pipe. The total head at a given point…

Q: An open circular cylinder with 2m of water is acted upon by an unbalanced upward force of 20 kN. The…

A: Given data in question Unbalanced force Depth of water Density of water Specific weight of water…

Q: A closed rectangular tank is 10m long, 2 m wide and 2.5m high is filled with water to a depth of 1.8…

A: Volume of the waterV=10×2×1.8=36m3=36,000Lwe knowdensity of water =1kgLso,M=36,000kg

Q: A container holds two layers of different liquids; one liquid has a specific gravity of 1.20 and 250…

A: Given data: specific gravity of liq1=1.20 Depth of liq2=250 mm specific gravity liq2=1.50 and 300…

Q: Q1:A plate (0.005 cm )distance from a fixed plate move at (72000 mm/min) and requires a force of…

Q: A stream of water, 3” in diameter, discharges into the atmosphere at a velocity 80.0 ft/sec. Find…

A: As given in the question, the water stream in discharging in the atmosphere with a velocity V. So…

Q: A cylindrical tank in which the hydrostatic pressure applied to it from the liquid column is (450…

A: Pressure at 8 m from the tank base = 400 kgf/m2 Pressure at 5 m from the base of the tank = 200…

Q: cylindrical tank containing a fluid (sg = 0.75) is accelerated upward by a net force of 40 lb. The…

Q: An open circular cylinder with 2m of water is acted upon by an unbalanced upward force of 20 kN. The…

Q: A closed compartment shown contains water h= 5 m deep at the left side and H =10 m deep on the right…

A: PA =75kPa To find pressure at point B

Q: Q1:A plate (0.005 cm )distance from a fixed plate move at ( 72000 mm/min) and requires a force of…

A: given Thickness = .005cm velocity = 72000mm/min force = 2.2m/s2

Q: Q6: The tank shown in Figure 5 containing oil and compressed air Pca = 50 (KN/m2). Find the pressure…

Q: sealed box filled with a liquid show below can be used to measure the acceleration of vehicles by…

Q: A jet of water (at 10°C) of diameter 2.5 cm flows freely in the atmosphere in a horizontal plane…

Q: Q1: - The block shown in figure below has a mass of 100 kg and is resting on 30° inclined surface.…

A: Chemical and physical reactions are two types of changes that can occur in a material or system. All…

Q: Q1:- A 300 mm diameter of pipes and 350 mm long slides along a large diameter cylinder at a speed of…

Q: PA PB A. 100 mm Liquid X 300 mm Liquid X ww 00 B.

Q: What flows through a 0.305m vertical pipe downwards at a rate of 1.70 x 10^(-4) m^3/s exiting into…

A: V=1.28m/s d=0.013m

Q: Gasoline (sg = 0.67) is flowing at 0.11 m3/s in the fabricated tube shown in Fig. 6.19. If the…

A: Given: The specific gravity of gasoline is 0.67. The speed at which gasoline is flowing is 0.11…

Q: For the inclined manometer containing mercury, shown in the figure, determine the pressure in pipe B…

Q: closed tank 3m in diameter and 3m high is filled with water and rotates about its axis at 100 rpm. A…

Q: horizontal plates which are 20 mm apart. The top plate is moving with a uniform speed 0.1 m/s. The…

A: Assuming laminar flow profile

Q: A cylindrical tank 0.8m high and a diameter of 0.3m is partially filled with water to a certain…

Q: Q.1.11 - MASS FLOW AT A PIPE JUNCTION Consider the steady flow in a water pipe joint shown in the…

Q: .) A pressure in a given tank reads 398 mm of Hg. Determine the equivalent height of a certain fluid…

Q: Calculate the capillary rise in a glass tube of 2.5mm diameter when immersed vertically in a) water…

A: Given, Diameter of capillary tube d = 2.5mm Surface tension for water σ = 0.0725N/m For mercury σ…

Q: The head of water at the inlet of a pipe 2000 m long and 500 mm diameter is 60 m. A nozzle of…

A: Given: Length of pipe, L = 2000 m Diameter, D = 500 mm = 0.5 m Head, H = 60 m Nozzle diameter, d =…

Q: An open cylindrical tank having a radius of 0.30 m. and a height of 1.20 m. is filled with water at…

A: Solution Given Data Radius of cylindrical tank= 0.30 m Height= 1.20 m Depth=0.90 m

Q: An open cylindrical tank having a radius of 300 mm and a height of 1.2 m is full of water. How fast…

Question

A plate 0.05 mm distant from a fixed plate moves at 1.2 m / s and requires a force of 2.2 N / m² to maintain this speed. Find the viscosity of the fluid between the plates.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Given

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A plate 0.025mm distant from a fixed plate moves at 60cm/s and requires a force of 2N/sq. m to maintain this speed. Determine the fluid viscosity between the plates.
Two plates each having and area of 5m^2 and and 37 mm apart. The plate on top is fixed while the plate located at the bottom is pulled using a force equal to 26 N resulting to a constant velocity of 45 cm/s. Determine the viscosity of the fluid filling the space in between the two plates.
An old pipe of diameter 2.5” is carrying water at a velocity of 4 ft/s. Determine the Reynolds number of the flow and the friction factor of the pipe if the length of pipe is 200ft and the kinematic viscosity of water is 0.98x10-6 ft2/s.
A cylindrical vessel 15 cm diameter and 40 cm long is completely filled with water. The vessel is open at the top. Find the quantity of water left in the vessel in cm^3, when it is rotated about its vertical axis with a speed of 300 rpm.
Q7. If the surface tension at air - water interface is 0.069 N / m, what is the pressure difference between inside and outside of an air bubble of diameter 0.009 mm?
A storage tank has vertical sides and is filled with water to a depth of 1.5 m. On top of the water is found an additional layer of oil (SG = 0.8) with a thickness of 0.5 m. Assuming a unit thickness into the page, calculate the following: (a) Resultant force on the wall of the tank due to the fluids? (b) Moment caused by the fluids along the wall at the base of the tank?
A tank containing water moves horizontally (parallel to length) with a constant linear acceleration of 3 m/s2 . The tank is 3 m long and the depth of water when the tank is at rest is 1.5 m. FIND THE FOLLOWING: A. what angle (degrees) does the water make during acceleration? B. what is the minimum height of the vessel for no spilling of water? C. what is the maximum pressure head? (m)
Q3) when we put in the class tube have diameter 1.5 mm liquid with mass density900 kg/m3 , the liquid rise in the tube about 15 mm . Calculate the surface tension force?
diameter = 60 cm height = 60 cm The CLOSE cylindrical tank is two-thirds full of water. It is subjected to pressure = 10 kpag. Considering that the tank is to rotate about the axis at the center at 10 rad/s a. What is the pressure at point C? b. What is the pressure at point D?
A 150-lb cylindrical tank is at rest as shown. Determine force P in lb required to move the tank up the higher-level surface.
A flat plate of area 1.5x10 6 mm2 is pulled with a speed 0.4m/s relative to another plate located at a distance of 0.15mm from it. Find the force required to maintain this speed if the fluid separating them has a viscosity of 1 poise.
Water floes through a circular pipe with a constant radius of 8cm. The speed and pressure at point a is 6 m/s and 300000 Pa respectively.a.) what is the speed of fluid at point b?b.) what is the pressure at point b which is higher than point a for about 5cm?