2 m 1.5 m-

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 13 kN applied at A. Assume a…

A:

Q: Member B is subjected to a compressive force of 800 lb. If A and B are both made of wood and are 1.8…

A: Given Data: The compressive load to member B is, P=800 lb. The thickness of materials is, t=1.8 in.…

Q: The way to the column where the loading status is seen determine the P load required for the 5 mm…

A: Given that,

Q: The steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. is carrying a load P=…

A:

Q: Determine the magnitude of the load P that will cause a maximum normal stress of smax = 30 ksi in…

A: Draw the free-body diagram of the structure.

Q: The rigid beam is supported by a pin at A and aluminum wires BD and CE. If the beam displaced 3.4 mm…

A: Given data          If the beam displaced by…

Q: The rigid beam is supported at its ends by two A-36 steel tie rods. The rods have diameters dAB =…

A: Draw the free-body diagram of the beam.

Q: Determine the average normal stress on each bar if subjected to the load shown. Three hanger bars…

A:

Q: The tension member is fastened together using two bolts, one on each side of the member as shown.…

A: Given data: Diameter of bolt, d = 0.3 in. Shear stress, τ = 12 ksi Normal stress, σ= 20 ksi The free…

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 11 kN applied at A. Assume a…

A:

Q: The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 26 mm. Assume…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 14 kN applied at A. Assume a…

A: Given data: F1=14 kNa=290 mmb=110 mmc=70 mmθ=40°dp=25 mmt=25 mm Need to determine the shear stress…

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 13 kN applied at A. Assume a…

A:

Q: The bronze C86100 pipe has an outer diameter of 1.5 in. and a thickness of 0.125 in. The coupling on…

A: Given data as per question Outer diameter of pipe = 1.5 in Thickness = 0.125 Force ,F = 20 lb

Q: The solid 1.25-in.-diameter rod is subjected to a uniform axial distributed loading along its length…

A:

Q: If the 2-in.-diameter shaft is made from brittle material having an ultimate stress of sult = 50…

A: Given data as per the question the diameter of the shaft = 2 in ultimate stress of shaft = 50 ksi…

Q: If the allowable bearing stress for the material under the supports at A and B is b = 800 psi,…

A: Given that: Cross sectional area of the beam  = 5*5 in2 Maximum stress = 800 psi Under the given…

Q: If the allowable bearing stress for the material under the supports at A and B is Op = 770 psi,…

A:

Q: Determine the stress in member CE assuming that the area in steel is 24 mm^2 p= 5 kN 3m 2m 2m 2m

A:

Q: The solid circular rod has a cross-sectional area of 410 mm². It is subjected to a uniform axial…

A: To Find : the normal stress in the rod at x=0.5m Given :  cross sectional area of rod A=410mm2…

Q: section bar of length (300mm) carries an axial (Q1)A (25mm) square cross- compressive load of…

A: As per our guidelines we have to answer only one question. So, post the question seperately and…

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 18 kN applied at A. Assume a…

A:

Q: The 6061-T6 aluminum bar has a square cross section of 25 mm by 25 mm. If it is 2 m long, determine…

A:

Q: The solid circular rod has a cross-sectional area of 450 mm2. It is subjected to a uniform axial…

A:

Q: The rigid bar is pinned at A and supported by two aluminum rods, each having a diameter of 1 in., a…

A:

Q: Determine the shear stress at point B on the web of the cantilevered strut at section a–a.

A: Given Applied loads 2 kN and 4 kN To find Shear stress at point B

Q: A 2" diameter pin connects the three links as shown. The links have a 3" by 3" cross- section.…

A:

Q: The plastic block is subjected to an axial compressive force of 600 N. Assuming that the caps at the…

A: Given: The length of the plastic block is L=100 mm=0.1 m. The breadth of the plastic block is b=50…

Q: The beam is supported by a pin at Cand by a short link AB. Each pin has a diameter of 10 mm. Assume…

A:

Q: The two pieces of wood, 150mm x 200mm, are glued together along the 55° joint. Determine the maximum…

A:

Q: The assembly consists of two rigid bars that are originally horizontal. They are supported by pins…

A: Draw the free body diagram of the given figure and show the forces on it as shown below:

Q: The beam is supported by a pin at Cand by a short link AB. Each pin has a diameter of 12 mm. Assume…

A:

Q: If the allowable bearing stress for the material under the supports at A and B is σb = 840 psi,…

A:

Q: Question 3 The frame is subjected to the load of 4 kN which acts on member ABD at D. Determine the…

A:

Q: Question: Determine the average shear stress in the single pin A and double pin B as well as the…

A: The UDL can be converted to point load by taking the area of the applied load surface and point it…

Q: Determine the maximum allowable load P that can be safely supported by the frame if t = 1.25 in. and…

A: Given data as per the question t=1.25 in b=3.5 in normal failure stress of σfail = 6 ksi Shear…

Q: The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 26 mm. Assume…

A:

Q: The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the…

A: Given data: The allowable bearing stress of the washers on the boards, (σb)allow = 2 ksi. The…

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 13 kN applied at A. Assume a…

A: Given: Let us consider the given data, F1=13 kN=13×103Na=300 mmb=190 mmc=90 mmθ=35°d=31 mmt=26 mm To…

Q: The rigid bar is pinned at A and supported by two aluminum rods, each having a diameter of 1 in. a…

A: P=20 Kips =88.964432 kN L1=distance between the point A to C =0.3048 m ; L2=distance between the…

Q: The solid 1.35-in.-diameter rod is subjected to a uniform axial distributed loading along its length…

A:

Q: The block is subjected to the eccentric load shown. Sketch the normal-stress distribution acting…

A: Given Applied load = 150 kN To find The normal stress distribution

Q: If the load P= 60N on the beam causes the end C to be displaced 10 mm downward: a) determine the…

A: Given-Data:- P=60N Assuming the length BD=4m To-Find:- a) Normal Strain in BD b) Shear Stress in…

Q: Determine the minimum diameter d to the nearest 18 in. of the rod to safely support the load. The…

A: Gven: σ=22 ksiτ=10 ksi

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 12 kN applied at A. Assume a…

A:

Q: An axial force of 52 kN is applied to the assembly shown by means of rigid end plates. 5 mm 5 mm 20…

A:

Q: The rigid beam is supported at its ends by two A-36 steel tie rods. If the allowable stress for the…

A: τA=allowable stress for the steel=16.2 ksi ;load (w)= 3 kip/ft ;(x)= 4 ft ;

Q: Member (1) has an area of 2,200.00 mm2 and an allowable normal stress of 180.00 MPa. Member (2) has…

A:

Q: applied load of P = 480 N causes the upper frame to be deflected downward by 4.9 mm. Determine the…

A:

Q: The timber member has a cross-sectional area of 1850 mm² and its modulus of elasticity is 12 GPa.…

A: