I need just öne answer Quiz0..If the load P= 60N on the beam causes the end C to be displaced 10 mmdownward:a) determine the normal strain in wire BD.b) Determine the shear stress in bolt A if it is doubled sheared and has adiameter of 2 cm.Dc) Determine normal stress in cable BD if it has a diameter of 1 cm.d) If the failure stress for the cable material is ofail = 1 MPa, will thestructure fail under the applied forces?AB3 m- 2 m2 m

Given-Data:- P=60N Assuming the length BD=4m To-Find:- a) Normal Strain in BD b) Shear Stress in…

If the load P= 60N on the beam causes the end C to be displaced 10 mm downward: a) determine the normal strain in wire BD. b) Determine the shear stress in bolt A if it is doubled sheared and has a diameter of 2 cm. c) Determine normal stress in cable BD if it has a diameter of 1 cm. d) If the failure stress for the cable material is orail = 1 MPa, will the structure fail under the applied forces? A В 2 m-- -3 m 2 m

If the load P= 60N on the beam causes the end C to be displaced 10 mm downward: a) determine the normal strain in wire BD. b) Determine the shear stress in bolt A if it is doubled sheared and has a diameter of 2 cm. c) Determine normal stress in cable BD if it has a diameter of 1 cm. d) If the failure stress for the cable material is orail = 1 MPa, will the structure fail under the applied forces? A В 2 m-- -3 m 2 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A stress element in a rock mass making up a slope experiences a 2D stress as follows: σx = 8 MPa, σy = 4 MPa , tauxy = 3 MPa a. Draw the Mohr circle. On Mohr's circle, mark the location of the x and y planes, mark the angle of rotation θ from the x plane to the σ₁,σ3,and taumax plane. Prove that the angle of rotation of the Mohr circle is 2 times the angle of rotation of the element. b. Write down the coordinates of the center of Mohr's circle and calculate its radius.
Question 3 3. A string 4 mm in diameter has original length 2 m. A force of 200 N. pulls the string. If the final length of the spring is 2.02 m, determine: (a) stress (b) strain (c) Young's modulus.
Please answer the problem completely. Show a free body diagram. Final answer: Shear stress = 3.2 mpa
For the direct shear example shown below, if F = 47 kN, AAB = ACD = 3151 mm2, the average shear stress in the internal vertical surface AB (or CD), = ______ MPa. Calculate your answer to 1 decimal place.
STRENGTH OF MATERIALS (Please write the complete solutions and FBDs completetely and correctly. No long explanation needed.Thumbs up will be given) A loaded beam, 60 mm wide by 200 mm high and 8 in long, has the shear and moment diagrams as shown below. (a) Determine the magnitude, type and location of the maximum flexural stress (b) Determine the type and magnitude of stress in a fiber 40 mm from the top of the beam at a section 2.5 m from the left end, Express final answers in MPa. (Use I=bh3/12
PLS ANSWER IN 20MINS IF POSSIBLE. THANK YOU The five-bolt connection shown in the figure must support an applied load of P = 295 kN. If the average shear stress in the bolts must be limited to 120 MPa, determine the minimum bolt diameter that may be used for this connection.
P = 80 kN σt = 150 MPa t = 8.0782 mm Can you help me solve for d2?
Q1-Calculate the force needed to guillotine a sheet of metal 5 mm thick and 0.8 m wide given that the ultimate shear stress is 50 MPa.
A rosette consisting of 3 gages forming, respectively, angles of θa, θb and θc with the x-axis is attached to the free surface of machine components made of material with a given Poisson’s ratio v and Modulus of elasticity E as shown in Fig. 6. Take note that strain values given above are the gage readings and not principal strains.
A 6 ft long solid steel shaft with a diameter of 4 inches transmits 250 hp at a speed of 250 rpm. Determine whether the following two requirements are satisfied: a) The maximum shear stress is not to exceed 10,000psi b) The angle of twist is not to exceed 1 degrees. Answers: a) 5016 psi, b) 0.862 degrees I'm unsure of how to solve for these answers. Please walk me through step-by-step. Please write clearly- Thanks in advance.
The allowable stresses for the splice shown are the following: 150 MPa for shear of rivets, 1.35Fy for bearing,0.60Fy for tension and Fy = 250 MPa. Note: rivet holes are 2 mm bigger than the rivet diameter and the middleplate is 20 mm thick. Find the diameter of the rivets so that the joint capacity due to shear approximately equal to the bearingcapacity.a. 25.4 mm c. 28.65 mmb. 30.79 mm d. 36.97 mm Find the maximum safe value of P without exceeding the allowable shearing stressa. 773.6 kN c. 938.3 kNb. 878.1 kN d. 848.2 kN Find the maximum safe value of P without exceeding the allowable tensile stress.a. 579.3 kN c. 716.1 kNb. 495.5 kN d. 692.5 kN
A rosette consisting of 3 gages forming, respectively, angles of θa, θb and θc with the x-axis is attached to the free surface of machine components made of material with a given Poisson’s ratio v and Modulus of elasticity E as shown in Fig. 6. Take note that strain values given above are the gage readings and not principal strains. PLEASE ANSWER I,G,H