True one P.2 n1.5 mABC3 m2 m2 m 1:16ols.liu.edu.lbA rigid beam is supported by a pin at A andtwo metallic wires at B and C. Determinethe force P that causes the point C todisplace downward by 0.1 mm.Given: E (wire B) = 70 Gpa, E (wire C) = 200%3DGpa and both wires have a diameter D = 6mm.Consider a linear elastic behavior.1.5A3 mSelect one:O P = 537 NO P = 573 NO P = 597 NO P = 287 NO P = 430 N%3D

Answered: Image /qna-images/answer/efdeed9c-f38b-4f02-8f3d-90b56254c940.jpg

Answered: 2 n 1.5 m C A 2 m 2 m 3 m

Engineering

Mechanical Engineering

2 n 1.5 m C A 2 m 2 m 3 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the modulus of elasticity of aluminum to be 10,000 lb / in2.Verify homogeneity in the units. An aluminum block of rectangular cross section is subjected to an axial compressive force, if the side measuring 1.5 in changes in length to 1.500132 in, determine the poisson's ratio and the new length of the side measuring 5 cm.
A 100 × 50 × 25mm steel block is subjected to a hydrostatic pressure of 5 MPa. The Young's modulus and Poisson's ratio of the material are 150GPa nd 0.2 respectively. The change in the volume of the block in mm³ is
You and your team are conducting a restoration project at an old city hall to investigatethe condition of the old chandelier at the main hall. The chandelier was estimated toweigh 4800 N and supported by three cables as shown in Figure 1. The project requiresyou to investigate the condition of the cables holding the chandelier after many years.Given the diameter of cable B is 6mm, while diameter of cable C is 1.25 times and cableA is 1.5 times of cable B, analyze the stress condition of the cables and propose a suitableinclination of the cable B to maintain the normal stress in cable C to be 0.5 times thanthe normal stress of cable B in order for the cable to support the chandelier
A spring is compressed by 0.05 in for every 1 lbf of applied force. Determine the deflection of the same spring when the applied forces is 6.5 lbm .Let go= 32.0 ft/s2
Consider the modulus of elasticity of aluminum to be 10,000 lb / in2.Verify homogeneity in the units. An aluminum block of rectangular cross section is subjected to an axial compressive force, if the side measuring 1.5 in changes in length to 1.500132 in, determine the new length of the side measuring 5 cm.
P = 80 kN σt = 150 MPa t = 8.0782 mm Can you help me solve for d2?
A shallow foundation supported by a silty sand is shown in Figure 7.5. Given:Length: L = 2 mWidth: B = 1 mDepth of foundation: Df = 1 mThickness of foundation: t = 0.23 mLoad per unit area: qo = 190 kN/m2Ef = 15 x 106 kN/m2The silty sand has the following properties:H = 2 mμs = 0.4Eo = 9000 kN/m2k = 500 kN/m2/mUsing Eq. (7.17), estimate the elastic settlement of the foundation.
Q;Determine the stiffness and elasticity matrices of the system below:
A copper rod with a diameter of 19 mm, modulus of 110 GPa, and a Poisson’s ratio of 0.35 is subjected to tension within the elastic region. Determine the force ( in N) that will produce a reduction of 0.003 mm in the diameter. I The answer is supposed to be 14,063 but im getting something else. Can you show how its supposed to be 14,063
A steel rod of circular section tapes from 2 cm diameter to 1 cm diameter over a length of 50 cm. If the modulus of elasticity of the material is 2*10^ 6 kg/cm^ 2 , then the increase in length under a pull of 3000 kg will be
A sectional steel cable of 3.00 cm2 has a mass of 2.40 kg per meter. If the cable is 500 m long hanging on a vertical cliff, how far the cable is stretched due to weighs itself? Known young steel modulus 2.00 x 10¹¹ N/m2 . (b). If there are two climbers hanging on the cable, determine how far cable is stretched. The mass of climbers is 60 kg and 70 kg, respectively.
the facade of a house consists of two cylindrical pillars placed at 1 m at the ends of a beam, these pillars support a steel beam of 320 kg and 6 m in length. the center of mass of the beam is at 2.8 m starting from the left end. at each end a new circular column was placed in order to raise a second floor, each of these columns has a mass of 120 kg. if it is considered that the structure must support 2100 kg distributed every 1.5 m, what will be the reaction of each column in the lower zone?