2) The 50-kg wheel is connected to a 10-kg block as shown. The block is moving downward with a speed of 2.4 m/S, and suddenly, friction between the wheel and ground was applied, and caused the block to decelerate at 10.0 m/ S. A) Draw the FBD and KD for the wheel alone, and show all external and effective forces on these diagrams. B) Calculate the angular acceleration of the wheel. C) Assuming the wheel has angular acceleration of 25 rad/ S? find the acceleration vector of the center of mass of the wheel.

2) The 50-kg wheel is connected to a 10-kg block as shown. The block is moving downward with a speed of 2.4 m/S, and suddenly, friction between the wheel and ground was applied, and caused the block to decelerate at 10.0 m/ S. A) Draw the FBD and KD for the wheel alone, and show all external and effective forces on these diagrams. B) Calculate the angular acceleration of the wheel. C) Assuming the wheel has angular acceleration of 25 rad/ S? find the acceleration vector of the center of mass of the wheel.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q 1: Determine the maximum possible acceleration on a level road, assuming (a) fourwheeldrive, (b) rear-wheel drive, (c) front-wheel drive. Assuming the coefficient of static frictionbetween the tires and the road is 0.8.
The system shown below is made up of two pulleys attached to the same shaft, with radii ri and re of 0.29 mm and 0.43 mm, respectively. The total mass of the pulley system is 14 kg and its turning radius is 0.26 mm from its center. The mass of block A is 9 kg and the mass of block B is 2 kg. If the coefficient of kinetic friction between block B and the floor is 0.2, find the angular acceleration of the pulley.
The conveyor belt shown below is inclined at an angle of 25 degrees. A 3kg package B is placed on the conveyor belt at the position shown with an initial velocity of 0 m/s with respect to the ground. The belt is moving quite fast, and as one could imagine the package is initially slipping, but it's accelerating at a rate of 3.05 m/s^2 until it catches up to the velocity of the belt. If this is the case, find the coefficient of friction between the belt and the package.
The combined mass of the motorcycle and its rider in Fig. a, and b is 250 kg. The mass center is at C. The wheels are locked when the brakes are applied at high speed. The coefficient of kinetic friction is 0.5, and the angular acceleration is zero. Determine the acceleration a
A bar of 30 kg mass is in the rest position for the position θ = 0 °, for which the spring is in its unstretched (relaxed) state. Find the angular velocity of the bar when it is at the position θ = 90 °. Take the acceleration due to gravity as 9.81 m / s ^ 2
In the figure, masses of a sphere of radius r and mass m are compressed between two neglected rods. The length of the bars is indicated by l, and the angle they make with the vertical by the angle. The force applied from the ends of the rods is in the horizontal direction and its magnitude is given by P. Friction between sphere and rods is neglected. Therefore, find the acceleration of the sphere in the vertical direction when the angle is 30º in terms of the given magnitudes. Note: Treat the sphere as the material point.
A rope drum on a E3.35rough surface is set into motionby pulling the rope with a constantforce F0.Determine the acceleration ofpoint C assuming that the drumrolls (no slipping). What coefficientof static friction μ0 is necessaryto ensure rolling?
The mass of the m_1 block in the figure is 40 kg, and the mass of the m_2 block is 10 kg. There is no friction between the m_1 block and the ground. The friction coefficient between m_2 and m1 is 0.6 and the kinetic friction coefficient is 0.4. A horizontal force of F = 100 N started to pull the m_2 block as shown. In this case, calculate the accelerations of m_1 and m_2 blocks?
2) The 50-kg wheel is connected to a 10-kg block as shown. The block is moving downward with a speed of 2.4 m/S, and suddenly, friction between the wheel and ground was applied, and caused the block to decelerate at 10.0 m/ S 2.A) Draw the FBD and KD for the wheel alone, and show all external and effective forces on these diagrams.B) Calculate the angular acceleration of the wheel.C) Assuming the wheel has angular acceleration of 25 rad/ S 2 find the acceleration vector of the center of mass of the wheel.
consider the mass and pulley system in the attached file. mass m1 = 29 kg and mass m2 = 12kg. the angle of the inclined plane is given and the coefficient of kinetic friction between mass m2 and the inclined plane is uk = 0.12. assume the pulleys are massless and frictionless what is the acceleration of mass m2 on the inclined plane? take positive acceleration to be up the ramp a2 = ?
A uniform drawbridge must be held at a 37° angle abovethe horizontal to allow ships to pass underneath. The drawbridge weighs45,000 N and is 14.0 m long. A cable is connected 3.5 m from thehinge where the bridge pivots (measured along the bridge) and pullshorizontally on the bridge to hold it in place. If the cable suddenly breaks, what is the magnitude of the angular acceleration of the drawbridge just after the cable breaks?
The piston of a 60° twin V-engine has strokes of 126 mm. The connecting rodsdriving a common crank has a length of 202 mm. The mass of the reciprocatingparts per cylinder is 1.2 kg and the speed of the crank shaft is 2000 rpm. Determinethe magnitude of the primary and secondary forces.