i need part 2 of this question Problem 1 Please choose the correct answer and also write down your solution.(1) The beam is subjected to the shown loading. What is the correct statement regarding the flexural stress atA and B?PPa. Both og and og are tensile stress.0.5 m0.5 m0.5 mb. Both oa and og are compressive stress.Og is tensile stress and og is compressive stress.с.d. OA is compressive stress and og is tensile stress.AВ(2) The cantilever beam is subjected to the load P and has cross section as shown. What is the ratio of themagnitudes of the maximum tensile and compressive flexural stresses over the a-a cross section?b. 3/7a. 7/2d. 2/10е. 3/10h. 10/3c. 7/3f. 10/2i. 1/1g. 2/7250 mm20 mm60 mm200 mm2 m1 m15 mm15 mm

when a point load acts on cantilever top portion is under tensile stress and bottom is compressive

(2) The cantilever beam is subjected to the load P and has cross section as shown. What is the ratio of the magnitudes of the maximum tensile and compressive flexural stresses over the a-a cross section? b. 3/7 с. 7/3 f. 10/2 i. 1/1 а. 7/2 e. 3/10 h. 10/3 d. 2/10 g. 2/7 250 mm- 20 mm 60 mm i C 200 mm -2 m -1 m 15 mm 15 mm

(2) The cantilever beam is subjected to the load P and has cross section as shown. What is the ratio of the magnitudes of the maximum tensile and compressive flexural stresses over the a-a cross section? b. 3/7 с. 7/3 f. 10/2 i. 1/1 а. 7/2 e. 3/10 h. 10/3 d. 2/10 g. 2/7 250 mm- 20 mm 60 mm i C 200 mm -2 m -1 m 15 mm 15 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The figure below are 2 solid cylindrical bars joined together at point B. Find the required minimumvalues of “d” of each bar if the normal stress is limited to MN ksi. complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94
How are the normal stresses distributed in the cross section in case of pure tension? (a) unevenly (b)linearly (C)there are no normal stresses (D)as a function of y (E)as a function of z (F)evenly
X= 460 lb. Find the stress at points A and B. Determine the point where the neutral axis intersects like ABD. The neutral axis intersects AB at (blank) inches from A and intersects BD at (blank) inches from D.
Calculate the shape factor and fully plastic moment Mp of the section shown in above figure . Assume yield stress =σy, in both tension and compression .
1. Determine the values of shear and moment at points where change in loads occur using the Area Method. Mark maximum values.2.Draw the shear and moment diagram. Show computation. 3. Solve the moment of inertia of the cross-section of the beam about the neutral axis. Show computation and box your answer.4. Compute the maximum shear stress. Show computation.5. Compute the maximum tensile and compressive flexural stress.
Before the 400 kN load is applied, the rigid platform rests on two steel bara, each of cross sectional area 1400mm^2, as shown in the figure. The cross sectional area of the aluminum bar is 2800 mm^2, Use E=200 GPa for steel and E = 70 GPa for aluminum. NEGLECT the weight of the platform A.) Compute the stress in the aluminum bar in Mpa after the 400 kN load is applied Choices: 45.64,16.30,40.62,14.51 B.) Compute the stress in the steel bar in Mpa Choices: 68.03,95.24,128.35,126.56 C.) Compute the shortening of the steel bar in mm. Choices: 0.125,0.085,0.113,0.158
PLEASE ANSWER ASAP TY! a) Determine the cross-sectional area of the structural tube (in mm2) b) Determine moment of inertia of the cross-section about the neutral axis (in mm4) c) What is the maximum normal stress at point K (in MPa)? Include negative sign if compressive. d) What is the axial stress at section H-K (in MPa)? Include negative sign if compressive. e) What is the flexural stress at section H-K (in MPa)? f) What is the maximum normal stress at point H (in MPa)? Include negative sign if compressive.
The cross sectional area of the bar ABCD is 545 mm2F1 = 15 kNF2 = 20 kNF3 = 40 kNDetermine the normal stress in bar AB, BC, and CD & the maximum normal stress. Specify if answers are tension or compression.
The figure below are 3 solid cylindrical bars joined together by a flange. Find the axial stress of eachbars complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94
Determine bending stress formula
Direct stresses of 120 N/mm2 (tension) and 90 N/mm2 (compression) are applied at a particular point in an elastic material on two mutually perpendicular planes. The principal stress in the material is limited to 200 N/mm2 (tension). Calculate the allowable value of shear stress at the point on the given planes. Determine also the value of the other principal stress and the maximum value of shear stress at the point using Mohr’s Circle.
Determine total stress and effective stress at point A