2) You were engaged as a consulting engineer to carry out a structural assessment on an existing reinforced concrete building and encountered a beam with the cross-section shown in Figure 2 below. Non-destructive tests carried out revealed that the material strengths are f = 3000 psi and fy = 60,000 psi. Determine the design moment capacity of this beam section. C.S.Z) (27 in.) (21.5 in.) E 2 #9 4 #11 (14 in.) Figure 2

2) You were engaged as a consulting engineer to carry out a structural assessment on an existing reinforced concrete building and encountered a beam with the cross-section shown in Figure 2 below. Non-destructive tests carried out revealed that the material strengths are f = 3000 psi and fy = 60,000 psi. Determine the design moment capacity of this beam section. C.S.Z) (27 in.) (21.5 in.) E 2 #9 4 #11 (14 in.) Figure 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cylindrical rod having a diameter of 0.5in is subjected to tension. How much load is required to cause a 10-4in change in the diameter. Take Young’s modulus of rod as 11x106 psi and Poisson’s ratio as 0.33.
A rod of diameter 50 cm and length 6 m is hanging vertically and carries an axial loadof 10 kN at bottom end. Calculate the elongation of the bar at a distance 2 m from thebottom end. Take the unit weight of the rod material is 25 kN/m' and modulus ofelasticity of the material is 3x109 MPa.
A steel pipe of length L =7.0 ft, outside diameter d2 = 6.0 in., and inside diameter d1 = 4.5 in. is compressed by an axial force P 140 kN. The material has modulus of elasticity E = 30,000 ksi and Poisson's ratio v = 0.30. Determine the following quantities for the pipe: (a) the shortening (delta) (b) the lateral strain E' , (c) the increase Ad2 in the outer diameter and the increase Ad1 in the inner diameter, and (d) the increase At in the wall thickness.
A rod with a diameter of 13 mm and a length of 50 mm is subjected to a force of 50 kN. The diameter is reduced to 12.99265 mm. Determine: a. The modulus of elasticity. Answer: 200 GPa. b. Poisson's ratio. Answer: ν = 0.30 c. Shear modulus. Answer: G = 76.92 GPa. d. The deformation of the rod. Answer: δx = 0.09415 mm. Recommendation: Obtain the modulus of elasticity using the slope of the straight line.
A plate 0.035mm distant from a fixed plate, moves at 80 cm/s and shear stress is 2 N/m2 to maintain this speed. Determine the fluid viscosity between the plates.
The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 28 MPa, Sy = 28 MPa, and Sxy = 37 MPa. Assume β=tan−1(ba)=21.8∘β=tan-1(ba)=21.8∘, a = 5, and b = 2. Using the equilibrium equation approach, determine the normal and shear stresses σσ (positive if tensile, negative if compressive) and ττ (magnitude only) at this point on the inclined plane shown.
A 40mm diameter rod 6m long elongates 12mm under load of 240kN. The diameter decreasesby 0.028mm during the loading. Determine the following:a. The Poisson’s ratio of the material,b. The Young’s modulus of the material, andc. The modulus of rigidity of the material.
mechanics deformable bodies 1. A hollow steel shaft has an outside diameter of 220 mm and an inside diameter of 200 mm. Which of the following nearly gives the torque in kN-m that will cause stress of 75.5 MPa in the shaft?
A 100 kg block is resting on a smooth inclined surface. Determine the value of T to maintain equilibrium.
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! The compound shaft consists of solid steel and bronze shafts and hollow aluminum shaft (D= 2.25" and d=0.90''). It is subjected to two torques as shown in the figure. The moduli of rigidity for steel, aluminum, and bronze are 12x106 psi, 4x106 psi, and 6x106 psi, respectively. Determine the shearing stress developed in each material. Also, calculate the angle of twist incurred by the aluminum shaft.
Problem : Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hooke's Law (E) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters?b) Check whether the pressure vessel is safe or not? Given data: - The yield strength of the pressure vessel is σy = 250 MPa.The inner diameter of the vessel is d = 2 m.The pressure acting in the vessel is P = 10 Atm.The longitudinal stress is σL = 200 MPa.Hooke's Law (E) = 150 MPaThe radial stress is σR = -50 MPa.
The 700-N force is applied to the 100-kg block, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the block.