2. A 200-mm long bronze tube closed at both ends fits without clearance in a 70-mm hole in a rigid block. It has a diameter of 70 mm and a wall thickness of 5 mm. The tube then sustained an internal pressure of 4.5 MPa. Use v = 0.33 and E = 83 GPa. Compute the tangential stress in the tube. Answer: o, = 5.20 MPa

2. A 200-mm long bronze tube closed at both ends fits without clearance in a 70-mm hole in a rigid block. It has a diameter of 70 mm and a wall thickness of 5 mm. The tube then sustained an internal pressure of 4.5 MPa. Use v = 0.33 and E = 83 GPa. Compute the tangential stress in the tube. Answer: o, = 5.20 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hoop shrunk onto a hallow tube exert a contact pressure of 3 ksi on the tube. An internal pressure of 10 ksi is then applied to the tube. The inner and outer radii of the tube are 1.5 in and 2.5 in, and 2.5 in and 4 in for the hoop. What is the maximum tangential strss in the tube after application of internal pressure? Also plot tangential stress variation diagram across the section.
The uniform sign has a weight of 1500 lb and is supported by the pipe AB, which has an inner radius of 2.75 in. and an outer radius of 3.00 in. If the face of the sign is subjected to a uniform wind pressure of p = 150 lb>ft2, determine the state of stress at points C and D. Show the results on a differential volume element located at each of these points. Neglect the thickness of the sign, and assume that it is supported along the outside edge of the pipe.
Q. The shaft is hollow from A to B and solid from B to C. The shaft has an outer diameter of 80 mm, and the thickness of the wall of the hollow segment is 10 mm. Assume Shear Modulus = 12 x 106 Psi a. Determine the maximum shear stress developed in the shaft. b. Also compute angle of rotation at the end A.
A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding.
knowing that P = 18 Kips, determine the maximum stress when r = 0.45 in and r = 0.70 in
The same torque is applied to two tubes with identical metal sheets, determine the ratio of circle/square of the shear stresses. Given: r = 13 mm, S = 22 mm, and t = 2.85 mm.
state true/false. and if false justify For horizontal flow of a liquid in a rectangular duct between parallel plates, the shear stress varies from zero at the plates to a maximum at the centerline.
13) Diameter of the solid shaft AB is 130 mm. Determine the maximum shear stress in the solid shaft AB.
A short post constructed from a hollow circular tube of aluminum supports a compressive load of 250 kN (see figure). The inner and outer diameters of the tube are d1 = 9cm and d2 = 13cm, respectively, and its length is 100 cm. The shortening of the post due to the load is measured as 0.5 mm. Determine the compressive stress. (Disregard the weight of the post itself, and assume that the post does not buckle under the load).
Two solid cylindrical rods support a load of P = 25 kN as shown. Rod (1) has a diameter of 13 mm, and the diameter of rod (2) is 12 mm. Determine the axial stress in rod (1).
Referring to Figure Q2 (a), the vertical stress increase at point A is 25 kN/m2due to application of line loads q1 and q2. Determine the magnitude of q2.
An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The butt diameter is 450 mm and the tip diameter (the top of the pole) is 320 mm. The weight of the pole, cross arms, and wires is 33 kN. Assuming the pole transmits the load as a point load, find the change in vertical stress in kPa at 2 m depth. a. 17.8 b.393.9 c.63.0 d.3.9