A cylindrical pressure vessel isfabricated from steel platingthat has a thickness of 42 mm.The diameter of the pressurevessel is 450 mm and its lengthis 2.0 m. Determine themaximum internal pressure thatcan be applied if the longitudinalstress is limited to 140 MPa, andthe circumferential stress islimited to 60 MPa. * A cylindrical steel pressurevessel 400 mm in diameter witha wall thickness of 20 mm, issubjected to an internalpressure of 5 MN/m^2. (a)Determine the safe stressbetween the tangential andlongitudinal sections in thesteel. (b) To what value may theinternal pressure be increased ifthe stress in the steel is limitedto 120 MPa? (c) If the internalpressure were increased untilthe vessel burst, sketch the typeof fracture that would occur.

problem 1Givendiameter of the pressure vessel d=450 mm=0.45 mthickness t=42 mm=0.042 m,longitudinal…

A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 42 mm. The diameter of the pressure vessel is 450 mm and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.

A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 42 mm. The diameter of the pressure vessel is 450 mm and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow circular tube is subjected to a tension force of 30 KN, a tensile stress of 20 MPa was recorded.lf the outer diameter of the tube is 100 mm, the inner diameter will be eqaual to. a. 93.95 mm O b. 89.95 mm C. 85.95 mm o d. 91.95 mm
Make your solution organised and state assumptions. A penstock pipe 10m diameter carries water under a pressure head of 100m. If the wall thickness is 9mm, the tensile stress in the pipe wall is nearest to?A. 2725 B. 1090. C. 545 D. 110 E. NOTA
Problem # 4: The tank shown is fabricated from steel plate. Determine the minimum thickness of plate which may be used if the stress is limited to 42 MPa and the internal pressure is 1.5 MPa. USING BOTH TANGENTIAL AND LONGITUDINAL STRESS FORMULA.
The gate shown is hinged through a point A and is restrained from opening by a fixed ridge at point B. For a gate width of 7 feet. Determine: a. the magnitude and direction of the hydrostatic force acting on the gate using the PRESSURE PRISM CONCEPT. Illustrate and label the pressure diagram/ prism as part of your solution. express your answer in klps. b. magnitude and direction of the force exerted on the plate by the ridge. Illustrate abd label the FBD of the force system. Express your answer in klps.
Q3: The solid shaft is made of material that has an allowable shear stress of t allowabk 60 MPa. Determine the required diameter of the shaft to the nearest mm. 800 N.m 600 N.m 2.5m 2.5m
8. Two flat jacks, 12 in. square, are placed in the w: 3 mately circular test gallery 8 ft in diameter. na:!;a:;d ?: iﬁﬁ.ﬁ'ﬁf& placed in the side wall. Flat jack 2 is vertical, with its edge parallel to the axis of the gallery. The cancellation pressures measured were 2500 psi with FJ 1 and 900 psi with FJ 2. Estimate the initial stresses (vertical and hori- zontal). List your assumptions.
A thin cylinder of inner radius 725 mm and thickness 5mm subjected to an internal pressure of 6Mpa. Find average circumferential stress?
Que : A solid shaft is to transmit 450 KW at 180 RPM. If the shear stress is not to exceed 150 MPa. Find Diameter of the shaft.
A solid shaft 100 mm. in diameter is to be replaced with a hollow shaft equally strong and made of the same material. The outside diameter of the hollow shaft is 127 mm. The allowable shearing stress is 41.40 MPa. Determine; (a) the inside diameter (mm.) of the hollow shaft. (b) the thickness (mm.) of the hollow shaft.
8. Two flat jacks, 12 in. square, are placed in the wall and roof of an approxi- mately circular test gallery 8 ft in diameter. Flat jack 1 is horizontal, and placed in the side wall. Flat jack 2 is vertical, with its edge parallel to the axis of the gallery. The cancellation pressures measured were 2500 psi with FJ 1 and 900 psi with FJ 2. Estimate the initial stresses (vertical and hori- zontal). List your assumptions.
A fire extinguisher tank is designed for an internal pressure of 874 psi. The tank has an outer diameter of 4.5 in. and thickness of 0.08 in. Calculate the longitudinal stress, the circumferential stress, and maximum shear stresses (in-plane and out-of-plane) at the outer surface of the tank. (Assume that all internal pressures are gage pressures. Enter the magnitudes in ksi.) longitudinal 01 ksi circumferential ksi in-plane Tmax ksi out-of-plane Tmax ksi
Vertical stress due to a line load Homework: An inclined line load of magnitude 10 kN/m. Determine the increase of vertical stress Aoz at point A due to the line load. 10 KNm Univeiy of Al-Q 5m College Of Engi