2. A beam AB is loaded as shown. The beam is pin-connected to the wall at A. At Ba 10-inch diameter pulley is attached through frictionless bearing to the beam. A rope passes around the pulley and is connected to Cand D vertically above the extremities of the horizontal diameter of the pulley. Determine the pin reaction at A and the tension in the rope. Hint: Pin connection has vertical and hozirontal reactions.

2. A beam AB is loaded as shown. The beam is pin-connected to the wall at A. At Ba 10-inch diameter pulley is attached through frictionless bearing to the beam. A rope passes around the pulley and is connected to Cand D vertically above the extremities of the horizontal diameter of the pulley. Determine the pin reaction at A and the tension in the rope. Hint: Pin connection has vertical and hozirontal reactions.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.125P: The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A...

See similar textbooks

Similar questions

The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
A 363.8N horizontal steel shaft is suspended by a vertical cable from A and by a second cable BC which lies in a vertical transverse plane and loops underneath the shaft. Calculate the tension T1 (N) in the cable.
The distributed load is supported by a beam with a pin and a roller. Determine the reaction (magnitude and direction) on the supports (pin and roller).
Find the support reactions and joint force of the construction,shown on the figure ,if P=12 kN q=9 kN/m , M= 12 kN , and L=2m
Two men carry a load of 2 kN by means of two ropes fixed to the weight. One rope is inclined at 45º and the other at 30º to the vertical. Find the tension in each rope.
A boom hinged at the base of a vertical mast is used to lift a 2000 lb load. Find the tension in the cable and the reaction R at the end of the boom. The angle of the boom is 40 degrees with the horizontal and the cable is 60 degrees with the vertical mast. Pls include given, formula, fbd, and solution.
For the log brace shown, select the set of 3 Free Body Diagrams that would be used to solve for the tension in the rope EF given the weight of the log. Assume the ground and log are frictionless. 4 ft A 1.25 ft 25 ft 1.5 ft 3 ft G H O B 2.5 ft 1 ft ***select 3****
The pin at O can support a maximum force of 3.5 kN. What is the corresponding maximum load L which can be applied to the angled bracket AOB? A. 0.541 kN C. 2.632 kN B. 1.676 kN D. 3.091 kN
please is urgent The 7.8m steel I-beam has a mass of 800kg and is lifted into position by applying a force P on the trolley to which the lower end B is secured. Cable AC is tied center of the beam and is horizontal when B is exactly below C. Determine, in function of x, the force P needed to maintain equilibrium from x=0 to the value of x at which A' lies exactly below C. Find the maximum value of P and the corresponding value of x.
Statics-Two Force Members 1. Determine the force P required to maintain equilibrium of the pulley system, and the reactions at the ceiling. 2. Assume W=1.25kN 3. Show and clearly label all Free Body Diagram to determine solution.
ابحثوا بالملفات Q1 :Determine the tensions T₁ and T₂ in the ropes AB and CD as shown in the below Figure that were used to support a machine component has long 3 m and weight 2500 N, then discuss your results.
This structure is supported by a roller joint on the left and a pin joint on the top. Two loads, P have similar magnitudes of P = 650 N and the angle θ = 40°. The length L of both members is 1.5 m. The vertical load acts at the midpoint of the horizontal member. Solve for the reaction forces at the roller and pinned joints.