2. A circular frustum of cone made of iron is one meter high with diameters 0.60m at the base and 0.30m at the top. Find the a) weight and b) mass of this circular frustum of cone if density of iron is 7800kg/m3. b) 030m No. 2 1.00m 0 60m

2. A circular frustum of cone made of iron is one meter high with diameters 0.60m at the base and 0.30m at the top. Find the a) weight and b) mass of this circular frustum of cone if density of iron is 7800kg/m3. b) 030m No. 2 1.00m 0 60m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.13P: Figure (a) shows the cross section of a column that uses a structural shape known as W867...

See similar textbooks

Related questions

Q: 1. The cantilever beam is made of a W10 x 33 section. Determine the displacement and slope angle of…

Q: Two frictionless balls strike each other as shown. The coefficient of restitution between the balls…

Q: Q1 Two spur gears in a simple train shown in Figure Q1 are having the same module, m = 2 and their…

Q: 25m (a) The tubular rotor shaft of a wind turbine shown in Figure 3(a) is of 50 mm and 40 mm outer…

A: Given data:- Inner diameter = 40 mm Outer diameter = 50 mm Torque = 2.5 kN-m Moment = 3.6 kN-m Find…

Q: (b) Why are the clutch friction plates perforated? What is the purpose of installing coil springs in…

A: Clutch friction plates are perforated for coolant passage for heat dissipation. Perforation helps in…

Q: Explain the purpose of the relief valve and one-way check valve in an electric fuel pump. What type…

A: Given question: Explain the purpose of the relief valve and one-way check valve in an electric fuel…

Q: A manometer is used to measure the pressure of a gas in a tank. The fluid used has a specific…

Q: The Mayflower ship having a displacement of 27000 metric tons and a draft of 10.4 m in ocean (sp.…

Q: nnecting rod is made as I section? Why do some connecting rods have hole drilled from the small end…

A: The allows oil to pass from the big end to the thrust section where there is friction against the…

Q: Describe the features, components, electric propulsion systems, and working principles of electric…

A: given; Describe the features, components, electric propulsion systems, and workingprinciples of…

Q: Problem 4 An U tube of radius R and length L is filled with water. In equilibrium position the water…

A: Given data A u-tube of radius R and length L is filled with water. If the level of water is…

Q: Out of the camber and caster, which is measured first and why? How the camber angle can be adjusted…

A: Camber angle is the angle which is measured in the front elevation in-between the wheel plane &…

Q: Determine the X scalar component of the 100 pound force.

Q: Q2 A mass-spring system is shown in Figure Q2 with mi = 10 kg, m2 = 20 kg, kı = (10+P) N/m, k2 =…

A: Given data: m1=10 kgm2=20 kgk1=10+P N/mk2=10+Q N/mk3=20+R N/mwhereP=2Q=0R=1 “Since you have posted…

Q: 3. The Department of Highways at Dale City put up a signage with a thickness of 4 inch at the corner…

Q: Dtermne the reaction at the supports A and C of Structral Truss shown.

Q: Determine whether the first part of statement will INCREASE, DECREASE or have NO EFFECT in the…

Q: A block of mass 40 kg slides to the right due to the application of the force T. Neglect the mass of…

Q: A gas power cycle uses air as the working fluid and has two turbine sections as shown in the figure…

Q: For the frame structure as in the figure, determine the total moment at : MA ,MB, MO

Q: SITUATION: A cylindrical tank with radius 0.5 m and 2 m high weighs 1200 N. The tank is to float in…

A: Disclaimer: Since you have posted multiple questions we will solve the first question for you. If…

Q: For the truss shown, assume a cross sectional area of each member is 3.2 in? a. Calculate the stress…

Q: Theorem for composition of accelerations when convected motion is fixed-axis rotation a, = a, +a, +…

Q: Problems 1 and 2. Locate the centroid of the shaded area

Q: Determine the moments of inertia of the Z-section about its centroidal xo- and yo-axes. +130 mm 17…

A: Find the moment of inertia about its centroid.

Q: Calculate the following: i. The polar second moment of area, J

A: Given data Outer Diameter of the shaft = Do = 50 mm = 0.05 mInner Diameter of the shaft = Di = 40 mm…

Q: An iron bar 2.0 cm x 3.0 cm x 10.0 cm at a temperature of 95 °C is dropped into a barrel of water at…

A: The rate at which an exposed body changes temperature through radiation is approximately…

Q: naded area y 100 mm 140 mm 50 mm 140 mm -200 mm- 2.

A: Divide shaded area as shown above

Q: A sharp-edged orifice in the vertical wall of a large tank has a diameter of 25 mm. The coefficient…

Q: 4-An ideal reheat Rankine cycle operates between the pressure limits of 10 kPa and 8 MPa, with…

A: Answer: The cycle efficiency is 41 percent.

Q: EX IP the Howrate between two tanks is (a.s m/s), Ex: find CH)? KLE1.8 RL=1.3 Ls Soom LIE300 Di=300M…

Q: When the pressure inside a vessel is 22.75 psig. then the absolute pressure equal to:

Q: d Given: 9/8 in 2 in Diameter of bolt = 7/8 inch Diameter at the root of the thread (bolt) = 0.731…

Q: pute; ) the corresponding values of 0s and 0, for each link when the driving crank is in the…

Q: A triangular plate and two rectangular plates are welded to a straight bar AB. The welded unit…

A: Solution; Given Data: ω=7.5 rad/s Co-ordinates of different corners are: A: 04000B: 00300C:…

Q: A Cascade refrigeration system using flash tank and intercooler is operating an evaporator with a…

Q: A 6-cylinder, 4-stroke Sl engine with a bore of 125 mm and a stroke of 190 mm was supplied during a…

Q: Calculate the principal stresses o 1 at point A of cross-section aa. Data: L = 0.3 m; F = 0.9 kN.…

Q: Determine the magnitude of the pin reaction at D. A 60° D. AC = 0.9 m %3D 6. AB = BD B =0.6 m 10 kg

A: Find the magnitude of pin reaction at point D.

Q: The bar AF has a cross-sectional area of 400 mm. The average normal stress in region CD is 10 kN SKN…

Q: Q4 Explain in detail the advantage of two of the following: a) Lubrication in metal forming b)…

A: a) Advantages of lubrication in metal forming In metal forming, lubricant will minimize friction and…

Q: Given: Diameter of bolt = 7/8 inch Diameter at the root of the thread (bolt) = 0.731 inch Inside…

Q: Two spur gears in a simple train shown in Figure Q1 are having the same module, m = 2 and their…

Q: Consider two cases involving the parallel flow of dry air at V= 1.5 m/s, T∞=45°C, and atmospheric…

Q: A homogeneous cylinder is submerged into two layers of liquid composed of water at the top layer and…

Q: This "double" nozzle discharges water at 10°C, (Ph2o = 1000 ) into the atmosphere at a rate of 0.50…

A: Given data, Water is discharge to the atmosphere means that total flow rate through A and B, i.e.,…

Q: Q5 Explain by sketch only 5 of the following: 1- the effect of heat rolling on grain size 2- three…

A: The size and texture of hot strip grains, as well as their distribution over the strip thickness,…

Q: Q4 Explain in detail the advantage of two of the following: a) Lubrication in metal forming b)…

A: Given Lubrication Work part Flow stress To find Advantages

Q: Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for the…

A: Given data-T0=1300 N-mτ=40Mpa n=4σB=70Mpa μ=0.3

Concept explainers

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.

Question

2. A circular frustum of cone made of iron is one
meter high with diameters 0.60m at the base and
0.30m at the top. Find the a) weight and b) mass
of this circular frustum of cone if density of iron is
7800kg/m.
b)
030m
No. 2
1.00m
0 60m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

3. The roof of a water tower is composed of eight equal isosceles triangles whose vertices meet at the center of the roof. If the inclined edges measure 4.6 m and the height of the roof is 3 m, determine the surface area of the roof. 4. How many square meters of canvass are required for a conical tent 5.5 m high and 3 m. diameter if 10% of the material is wasted?
A block of stone is cut so that its cross‑section is a parallelogram. The width of the bottom side is ?=0.655 m, the height of the top of the block is ℎ=0.915 m, and the top right corner overhangs a distance ?oh=0.195 m from the bottom corner as shown. Assume that the block is of uniform density, so that the center of gravity of the block is located at the geometric center.
21 - A vertical cylindrical vessel with a diameter of 15 cm and a height of 40 cm is partially filled with 25 cm high water. The cylinder is rotated at a constant speed of 20 rad/s. What is the maximum height difference between the edge and the center of the free surface? a) 11.5cm B) 15cm NS) 5.4cm D) 9.5cm TO) 7.2cm 22 - The water level in a tank is 9.4 m above the ground. At the bottom of the tank, the sprinkler connected to the pipe end faces upwards. The effective pressure at the water surface inside the tank is 300 kPa. Since the system is at sea level, how high does the water coming out of the fountain rise? (ρ=1000 kg/m³) a) 48 meters B) 25m NS) 30m D) 40m TO) 20m
I want a step-by-step explanation of how to find the area. Consider the plane area shown where r = 12 in. a. Determine the volume and the surface area of the solid obtained by rotating the area about the x-axis. The area of the solid is 27.715 × 103 in2. b. Determine the volume and the surface area of the solid obtained by rotating the area about the y-axis. The area of the solid is 15.85× 103 in2
Solve it using step by step formula.. draw each of the step you will make. The answers are 733.16 m, 1.85m.
A 52.67-cm cube of ice melts, the liquid water is placed in a spherical container fillings it. If the specific volume of ice at 0°C is 1.094 cm³/g and of water is 1.002 cm³/g. compute for the diameter in cm of the spherical container. answer in 3 decimal places.
A conveyor 66 m long is inclined at an angle of 4 degrees to the horizontal and deposits material 8 m below its top end. Determine the distance the material is carried by this conveyor. Provide your answer in m and round to the nearest whole number.
A load bauxite has a density of 3.15 g/cm3. If the mass of the load is 135.5 metric tons how many dump trucks, each with a capacity of 12 cubic yards, will be needed to haul the whole load.
A column of mercury (density of mercury 13,534 g / cm) has a height of 10 ft. Considering a gravitational acceleration value of g = 9.80665 m / s and using the equation To calculate the hydrostatic pressure P = ρgh, determine the pressure exerted by the column of mercury in MPa. (Round the result to 2 decimal places.)
A centroid is an object's geometric center. For an object of uniform composition, its centroid is also its center of mass. Often the centroid of a complex composite body is found by, first, cutting the body into regular shaped segments, and then by calculating the weighted average of the segments' centroids.An object is made from a uniform piece of sheet metal. The object has dimensions of a = 1.05 ft , where a is the diameter of the semi-circle,b = 3.74 ft , and c = 2.45 ft . A hole with diameter d = 0.700 ft is centered at (0.925,0.525) . Part A Find the area of the body. (Figure 1) Express your answer numerically in feet squared to three significant figures. Part B Find x¯ , the x -coordinate of the body's centroid. (Figure 1) Express your answer numerically in feet to three significant figures. Part C Find y¯ , the y -coordinate of the body's centroid. (Figure 1) Express your answer numerically in feet to three significant figures.
Figure (a) shows the cross section of a column that uses a structural shape known as W867 (wide-flange beam, nominally 8 in. deep, weighing 67 lb/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following cross-sectional properties: A=19.7in.2,Ix=272in.4, and Iy=88.6in.4. Determine the dimensions of the rectangle in Fig. (b) that has the same Ix and Iy as a W867 section.
A vessel is in the form of an inverted regular square pyramid of altitude 9.87 in. and base edge 6.27 in. The depth of the water it contains is 6 in. a. How much will the surface rise when 1 pt. of water is added? ( 1 gal.=231 cu.in.) b. Find the wetted surface when the depth of water is 9.23 in.?