2. (a) Find the resultant of these three forces in vector form. (b) Find the magnitude of part (a) F₁ = 30 kip 50° 26° F₂= 35 kip

Q: how does mechanical efficiency affect net power output calculation of a gas turbine power plant.…

A: Any internal combustion engine that uses gas as the working fluid to turn a turbine is referred to…

Q: 2.10 Two forces are applied as shown to a hook support. Knowing that. Knowing that the magnitude of…

A:

Q: where does the equation -atheta  = rtheta** + 2r*theta* come from? More specifically where does the…

A:

Q: During heating and humidification process briefly describes how the psychrometric properties below…

A: Heating and Humidification Process: In Heating and Humidification psychometric process of the air is…

Q: Blocks A, B, C, and D have weights of 50 N, 25 N, 20, and 15 N, respectively as shown in Fig.3. All…

A: GivenWA=50NWB=25NWC=20NW=15Nμs=0.3

Q: The 14.2-in. spring is compressed to a 6.9-in. length, where it is released from rest and…

A: Given data:

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A:

Q: How do you determine the moment of inertia of a plane surface?

A: The moment of inertiaMoment of inertia of an elementry area about any axis is the product of the…

Q: Question The yield strength for an aluminum alloy that has an average grain diameter of 10 um is 400…

A: OPTION B -668MPa is the right answer.  Detailed explanation and solution of the above problem…

Q: Area = 800 mm² Area = 500 mm² A P B C 75 kN D 50 KN 1.75 m. 1.25 m. 1.5 m

A:

Q: We will explore an example that connects the basic definitions and equations for different modes of…

A:

Q: 1. For diagrams 1 and 2 below, using the Method of Components only (no other method will be…

A:

Q: Example-1:- V A rigid tank with a volume of 1.8 m3 contains 15 kg of saturated liquid- -: vapor…

A:

Q: Draw the FBD of the problem The coefficient of friction between the inner pulley and the belt is…

A:

Q: mes checks the pressure on his front left tire, and it reads 25 pound per square inch (psi). His…

A: pressure required=32psi current pressure=25psi

Q: A mass of 0.2 kg of saturated refrigerant- 134a is contained in a piston-cylinder device at 200 kPa.…

A:

Q: A 5m copper tube is heated externally to 100degC. Air is heated by passing it through the 40mm…

A: Given:Length of the copper tube, l=5 mTemperature of the copper tube, Ts=100°CDiameter of the copper…

Q: If the manometer top in the figure below is open, then the mercury level is 10 cm below the…

A: Given data: Pair=200 kPax=10 cm Need to determine the reading for H.

Q: Hot air at 80°C is blown over a 2-m x 4-m flat surface at 30°C. If the average convection heat…

A: given data flat surface temperature  Ts=30° hot air temperature  Ta=80° Surface area A=(2x4)= 8m2…

Q: A student drove to the university from her home and noted that the odometer reading of her car…

A: Given data: d1=12 kmt1=18 mind2=10.3 kmθ=25° douth of east Need to determine the average speed and…

Q: Q1 - The plate is subjected to the two forces at A and B as shown in Fig. 1. 1- Determine…

A: Given

Q: Situation 4. Determine the magnitude and coordinate direction angles of the resultant force acting…

A:

Q: Q2 A 2900-lb car is traveling at an altitude with air density of 0.00206 slugs/ft³. It has a gear…

A: Given              Mass, m = 2900 lb               Area, A = 20 ft2 Drag coefficient = 0.3…

Q: 500 MMSCFD of supercritical steam generated in the steam generator (shown in the sketch below) at…

A: Note: As per Guidelines only 3 part will be answered, please post again this question and asked for…

Q: A stone is thrown from the top of a building with an initial velocity of 20 m/s straight upward. The…

A:

Q: Electric power is to be generated by installing a hydraulic turbine-generator at a site 70 m below…

A:

Q: A fireworks show is choreographed to have two shells cross paths at a height of 103 ft and explode…

A:

Q: A 0.08 m³ drum contains saturated water and saturated vapor at 300 °C. If the volumes occupied by…

A: Given data, V = 0.08 m3      ( V = Volume of drum ) Tsat = 300°C Vf = Vg               ( Vf = Volume…

Q: A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at B,…

A:

Q: 000 rev/min, producing 168 ft-lb of torque. The drive axle slippage of 2%, 14-inch-radius wheels,…

A:

Q: 2. The intake of the compressor of an air-standard brayton cycle is 40,000 cfm at 15 psia and 90°F.…

A: The given information in the problem is listed in the following attached image:

Q: The car moves in a straight line such that for a short time its velocity is defined by v = (312+ 2t)…

A:

Q: Compute for (a) the force exerted on the bolt and rivets at joints A, B, and C and (b) the normal…

A:

Q: Compare and contrast my field's is mechanical engineering, English (i.e. Business English)  to…

A:

Q: Read and record the dimensions indicated by the letters A to E in Figure C-530, Figure C-53 6 8 2 9…

A: Draw the given diagram of ruler.

Q: 3-45. If a vertical force of 2.5 kN is applied to the hook at A, determine the tension in each of…

A: Here, A(0,0,3), B(1,-3,0), C(1,1.5,0) and D(-0.75,1,0) Tension in cables can be determined by…

Q: A placekicker is attempting to make a 41-yard field goal. If the launch angle of the football is…

A: The vertical and horizontal speed of the ball can be expressed as shown below. The horizontal…

Q: Cavalier oblique view . Cabinet oblique view.

A:

Q: At the beginning of compression in an ideal dual combustion cycle, the working fluid is 1 lb of air…

A:

Q: what is the magnitude of the resultant force due to the distributed load in the diagram above? Do…

A: In the given diagram, distributed force diagram is shown. It is required to determine value of the…

Q: The system contains fart gas at 300 kPa, with volume of 0.2 m3 and at 40°C. More fart is added at…

A:

Q: Determine the resultant of the three forces shown. Consider three forces P1, P2, and P3 such that…

A:

Q: Suppose that 0.27 kg of water is contained in a vertical cylinder/piston arrangement as a 2 phase…

A: Given: mw=0.27 kgT1=50°CV1=0.03 m3Mpiston=125 kgApiston=8.77 cm2=0.000877 m2Patm=101.325 kPa

Q: What is the magnitude of the resultant force due to the distributed load in the diagram? The use of…

A:

Q: Consider a one-dimensional plane wall of thickness 2L that experiences uniform volumetric heat…

A:

Q: 5. The s-t graph for a sports car moving along a straight road. Construct the v-t graph and a-t…

A:

Q: Consider a person whose exposed surface area is 1.7 m², emissivity is 0.7, and surface temperature…

A: Given data: A=1.7 m2ε=0.7Tper=32°C=305 K Need to determine the heat loss by the person.

Q: Compute for (a) the force exerted on the bolt and rivets at joints A, B, and C and (b) the normal…

A:

Q: Magnetic tape's widespread acceptance may be attributed to its many advantageous features.

A: Magnetic Tape's: Magnetic Tape is a kind of data storage which  used for storing digital information…

Q: Ammonia contained in a piston-cylinder assembly, initially saturated vapor at 0˚F, undergoes an…

A: