2. A flanged bolt coupling consists of seven 12-mm diameter bolts arranged on a bolt circle 300 mm in diameter, and five 12-mm diameter bolts on a concentric bolt circle 250 mm in diameter. Calculate the torque that can be applied if the allowable shearing stress in the bolt is 60 MPa. Answer: T = 10.66kN-m 3. Determine the number of 12-mm diameter bolts that must be used on the 250-mm bolt circle of the coupling mentioned in Problem 2 to increase the torque capacity to 12 kN-m.

2. A flanged bolt coupling consists of seven 12-mm diameter bolts arranged on a bolt circle 300 mm in diameter, and five 12-mm diameter bolts on a concentric bolt circle 250 mm in diameter. Calculate the torque that can be applied if the allowable shearing stress in the bolt is 60 MPa. Answer: T = 10.66kN-m 3. Determine the number of 12-mm diameter bolts that must be used on the 250-mm bolt circle of the coupling mentioned in Problem 2 to increase the torque capacity to 12 kN-m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A fluid having a specific gravity of 0.869 and dynamic viscosity of 0.0814 Pa-s flows through a cast iron pipe at a velocity of 1m/s. The pipe is 50 m long and has a radius of 75mm. Solve for the shearing stress at the walls of the pipe in Pa. Round your answer to 2 decimal places.
A circular copper rod having length of P inches is to be twisted by torques 6.5P lb.in until the angle of rotation between the ends of the rod is 3.0°. If the allowable shear strain in the copper is 0.0006 radians, solve for the maximum permissible diameter of the rod? (Where P is 27
1. For the riveted connection shown in the figure using elastic analysisa. Determine the safe value of P if the allowable shearing stress of 25mm rivets is 150MPab. Determine the maximum shearing stress that can be develop in the rivet for a given load ? = 52??c. Determine the minimum shearing stress that can be develop in the rivet for a given load ? = 52?N
A figure below is a 200-mm diameter pulley which was attached on a 60-mm diameter shaft and it applies a torque to the shaft equivalent to 2.2 kN-m. The allowable shearing stress in the key is 70 MPa. If the length of a key is 70 mm, determine the designed width of the key. 12 mm 14 16 15 mm
A flanged bolt coupling consists of seven steel 20mmϕ bolts spaced evenly around a bolt circle 300mm in diameter. Determine the torque capacity of the coupling if the allowable shearing stress is 40MPa. See figure 13
Three steel rods, each having a cross-sectional area of 500 mm2, are assembled in a symmetrical manner, ass shown in the igure. Assume that steek behaves as a linear elastic material with E= 200 GPa. Determine the deflection of joint A due to a downward force of P= 2MN
b. Calculate "P" in KN considering tension failure on net area Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
A 900 N-m couple is applied to the flywheel in the diagram. The minimum force X required to prevent rotation of the flywheel is also applied. If the coefficient of belt friction is 0.20, a. which tension is larger, TA or TB?Explain b. What is the angle of contact in radians? c. What is the value of the ratio TA/TB?
A compound shaft consists of a titanium alloy [G = 6,200 ksi] tube (1) and a solid stainless steel [G = 11,500 ksi] shaft (2). Tube (1) has a length of L1 = 50 in., an outside diameter of D1 = 2.55 in., and a wall thickness of t1 = 0.160 in. Shaft (2) has a length of L2 = 52 in. and a diameter of d2 = 1.35 in. If an external torque of TB = 520 lb·ft acts at pulley B in the direction shown, calculate the torque TC required at pulley C so that the rotation angle of pulley C relative to A is zero.
A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bolt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter db / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gb = 28 Gpa.
20mm Steel Plates in the figure shown are connected by 9 rivets with 20mm diameter. If the Allowable Shear stress for the rivet is 194 MPa and Allowable stress for bearing on the plate is 234 MPa, what is the maximum load P that can be applied in the connection?
A two pinned end bars AB (Copper), ? = 850 ??2, ? = 120 ??? and BC (Aluminum), ? = 1000??2, ? = 70 ??? is subjected to a horizontal force of 100 ?? applied at pin B as shown in the figure, determine the horizontal displacement of pin B.