2. A long steel pipe is subjected to a state of plane strain (ɛzz = Ezx = Ezy = 0) whenthe design loads are applied. At the critical point in the pipe, the non-zero stress143.28 MPa ,components are found to be oxx = 53.28 MPa , ơyyOxy40 MPa and o22 = 57 MPa . The material has a yield stress of= 245 MPa . Determine the factor of safety in the design based on the vonOyMises criteria.

Answered: Image /qna-images/answer/1bebba47-5b14-4bcd-ae4e-17c045c5caa8.jpg

2. A long steel pipe is subjected to a state of plane strain (8zz = Ezx = Ezy = 0) when the design loads are applied. At the critical point in the pipe, the non-zero stress 143.28 MPa , %3D components are found to be oxx = 53.28 MPa , ơyy Oxy 40 MPa and o22 = 57 MPa . The material has a yield stress of = 245 MPa . Determine the factor of safety in the design based on the von Oy Mises criteria.

2. A long steel pipe is subjected to a state of plane strain (8zz = Ezx = Ezy = 0) when the design loads are applied. At the critical point in the pipe, the non-zero stress 143.28 MPa , %3D components are found to be oxx = 53.28 MPa , ơyy Oxy 40 MPa and o22 = 57 MPa . The material has a yield stress of = 245 MPa . Determine the factor of safety in the design based on the von Oy Mises criteria.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A hollow steel tube with an inside diameter of 110 mm must carry a tensile load of 404 kN. Determine the tube's outside diameter (mm) if the stress is limited to 122 mPa. The final answer should have 2 decimal places
A steel cylinder is 160 mm ID and 320 mm OD. If it is subject to an internal pressure of 150 MPa, determine the tangential stress on the outside layer.
A hollow steel tube with an inside diameter of 106 mm must carry a tensile load of 404 kN. Determine the tube's outside diameter (mm) if the stress is limited to 123 mPa. The final answer should have 2 decimal pla
A steel bar 0.75 in. in diameter has an axial load P = 13,000 lbs. a. Determine the normal stress (in MPa) on the plane through the bar that forms an angle of 30 degrees with the cross-section. b. Determine the shear stress (in MPa) on the plane through the bar that forms an angle of 30 degrees with the cross-section. c. Determine the maximum normal stress (in MPa) on the bar and d. Determine the maximum shear stress (in MPa) on the bar
Answer the questions given the following stresses: a) The value of the minimum principal stress b) The value of the maximum principal stress c) The value of the angle resulting to zero shear stress is
The assembly consists of a brass shell (1) fully bonded to a ceramic core (2). The brass shell [E = 86 GPa, α= 18 × 10−6/°C] has an outside diameter of 33 mm and an inside diameter of 27 mm. The ceramic core [E = 320 GPa, α= 2.5 × 10−6/°C] has a diameter of 27 mm. At a temperature of 15°C, the assembly is unstressed. Assume L = 320 mm. Determine the largest temperature increase Δ⁢t that is acceptable for the assembly if the normal stress in the longitudinal direction of the brass shell must not exceed 65 MPa.
a) What is the stress in the bronze rod (in MPa)?b) What is the stress in the steel rod (in MPa)?
The maximum and minimum normal stresses is known as?
Determine the maximum load P that can be applied, knowing that the youngs modulus of the material is 70 GPa and the allowable stress is 22 MPa.
A hollow aluminum tube used is a roof structure has an outside diameter d2 and inside diameter d1. The tube is 2.5m long and the aluminum has a shear modulus of G=28 GPa. a.If the tube is twisted in pure torsion by torques acting at the ends,what is the angle of twist in degrees when the max shear stress is 50MPa? b.What diameter “d” is required for a solid shaft to resist the same torque with the same maximum stress? d1 = 90 (mm) d2 = 110 (mm)