2. A pump is to be used to fill two storage tanks. The pump is manually started by the operator from a start-stop station. When the first tank is full, the control logic must be able to automatically stop flow to the first tank and direct the flow to the second tank with float switches and electric solenoid valves. When the second tank is full, the pump must shut down automatically. Indicator lamps are to be included to signal when each tank is full. O full 2 full 1 FS1 FS2 SOL 1 TANK 1 TANK 2 SOL 2 PUMP Design a control ladder diagram that will imnlement this

2. A pump is to be used to fill two storage tanks. The pump is manually started by the operator from a start-stop station. When the first tank is full, the control logic must be able to automatically stop flow to the first tank and direct the flow to the second tank with float switches and electric solenoid valves. When the second tank is full, the pump must shut down automatically. Indicator lamps are to be included to signal when each tank is full. O full 2 full 1 FS1 FS2 SOL 1 TANK 1 TANK 2 SOL 2 PUMP Design a control ladder diagram that will imnlement this

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter33: Hydronic Heat

Section: Chapter Questions

Problem 24RQ: In a primary-secondary pumping arrangement, the largest circulator pump will be located A. in the...

See similar textbooks

Similar questions

Describe the difference between closed and open system
Suppose that you have designed a portable compressed-air supply system, as shown in the figure below,for filling scuba tanks and for driving pneumatics tools in garages and factories.The system consists of an electric motor, an air compressor, an air tank, a regulator and a pressure-reliefsafety valve.The regulator contains a pressure sensor connected to a power switch. The motor is switched on whenthe tank pressure drops bellow a fixed value and off at a slightly higher pressure. The pressure-reliefvalve is set to open at a higher pressure than the regulator motor off-pressure.Explosion of the tank is clearly a dangerous hazard. Three events are assumed to possibly lead to a tankexplosion:1. an internal tank defect such as poor welding2. an external cause such as a plant vehicle colliding with the tank3. Excess pressure in the tank. The excess pressure can occur only if both the control unit and thepressure-relief valve fail:The pressure sensor might fail to shut oof the motor because…
Match the fluid power system with its suitable applications/equipment
Choose correct answer: An air compressor forms a _______________ A. isolated system B. combined open and isolated system C. closed system D. open system
Lukewarm water at 60 degree c in a storage tank is being pumped at 300 L/min from the tank. The line from the storage tank to the pump suction is 5 m of 2 inches Schedule 40 steelpipe, and it contains four (4) elbows. The discharge line after the pump is 50 m of 1.5 inches Schedule 40 steel pipe and contains a fully opened globe valve and two (2) elbows. The water was discharged to the households at 15 m above the water level in the storage tank. All elbows have a 90° angle. Calculate all frictional losses
21.) How is the capability of a variable displacement pump changed by the addition of pressure compensation?
Describe the seven different parts that make up the Open System.
1.A technician is traversing a duct and obtains the following 8 velocity readings: 500 fpm, 400 fpm, 375 fpm, 625 fpm, 275 fpm,360 fpm,420 fpm, and 575 fpm. What is the velocity value that will be used for system calculations?
Briefly describe pump selection using characteristic curves provided by the pump manufacturer.
Define and discuss the important parts of the Duplex Pump.
Classify the air conditioner system if it is an open-loop or closed-loop system and give the reason of your choice, draw a simple block diagram with the name of input, output and control system used
Centrifugal pump transfer energy from __________ a. rotor to fluid b. rotor to impeller c. impeller to rotor d. fluid to rotor