2. A steel shaft (G = 80 GPa) of total length L = 3.0 mis encased for one-third of its length by a brasssleeve (G, = 40 GPa) that is securely bonded to the%3D%3Dsteel. The outer diameters of the shaft and sleeveare di = 75 mm and d2 = 90 mm, respectively. Themaximum shear stress in brass is 70 MPa, maximumshear stress in steel is 110 MPa and the maximumallowable angle of twist is 5°. What is the maximumallowable torque that can be applied at the ends ofthe shaft?BrassSteelshaftdi = 75 mmd2 = 90 mmsleeveTTAB1.0 m-L= 2.0 m-2= 2.0 md1dyBrass-sleeveSteelshaftd2d2

Given, Steel shaftGs=80 GPa Total length L=3 m Gb=40 GPa Diameter, d1=75 mmd2=90 mm Shear stress in…

2. A steel shaft (G, = 80 GPa) of total length L = 3.0 m is encased for one-third of its length by a brass sleeve (G, = 40 GPa) that is securely bonded to the %3D steel. The outer diameters of the shaft and sleeve are di = 75 mm and d2 = 90 mm, respectively. The maximum shear stress in brass is 70 MPa, maximum %3D shear stress in steel is 110 MPa and the maximum allowable angle of twist is 5°. What is the maximum allowable torque that can be applied at the ends of

2. A steel shaft (G, = 80 GPa) of total length L = 3.0 m is encased for one-third of its length by a brass sleeve (G, = 40 GPa) that is securely bonded to the %3D steel. The outer diameters of the shaft and sleeve are di = 75 mm and d2 = 90 mm, respectively. The maximum shear stress in brass is 70 MPa, maximum %3D shear stress in steel is 110 MPa and the maximum allowable angle of twist is 5°. What is the maximum allowable torque that can be applied at the ends of

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
A solid aluminum shaft of 108 mm diameter fits concentrically in a hollow steel tube. Determine the minimum internal diameter in mm of the steel tube so that no contact pressure exist when the aluminum shaft carries an axial compressive load of 547 KN. Assume Poisson's ratio = 1/3 and a modulus of elasticity of the aluminum rod is 75 GPa. Use 4 decimal places.
Given: A steel rod (A = 150mm^2) is stretched between two fixed points with a tensile load of 5000N at 20degree C. determine: a) the stress at -20 degree C b) at what temperature will the stress be zero *DRAW THE FBD: COMPLETE SOLUTION *USE 3 DEC PLACES
A flat bar of a width b = 60 mm and thicknesst = 10 mm is loaded in tension by a force P (seefigure). The bar is attached to a support by a pin ofa diameter d that passes through a hole of the samesize in the bar. The allowable tensile stress on the netcross section of the bar is σT = 140 MPa, the allowableshear stress in the pin is τS = 80 MPa, and theallowable bearing stress between the pin and the baris σB 5 200 MPa.(a) Determine the pin diameter dm for which theload P is a maximum.(b) Determine the corresponding value Pmax of theload.
A three part bar is connected to walls at D and C and loaded as shown. Middle section AB is solid A36 steel with a 20 mm diameter (E = 200 GPa). Outer sections DA and BC are solid red brass (E = 101 GPa) with a 50 mm diameter. A previous analysis by a now departed coworker correctly determined that the internal normal stress in DA was 54.952 MPa compression. You are asked to determine the horizontal displacements of joints A and B.
A 1 meter long steel rod AB of 15-mm diameter is held snugly (without any initial stresses) between rigid walls by the arrangement shown in the figure. (STEEL ROD : E = 200 GPa , α= 12 x 10-6/°C , and yield strength σY = 250 MPa.) a) If the rod undergoes a temperature drop of 24°C, and the bolt at B is tightened causing the rod to elongate by 0.0566 mm, determine the bearing stress between the washer and the wall. b) Determine the amount of temperature drop that is allowed if the factor of safety against yieldingis 4.
2. The bronze bar 3 m long with a cross-sectional area of 350mm2 is placed between two rigid walls. At a temperature of -20 oC, there is a gap of 2.2 mm. Find the temperature atwhich the compressive stress in the bar will be 30 MPa ifthe bar will experience:a. No tensile.b. With an tensile of 5,000 N.Use α = 18.0 x 10-6 /oC and E = 80 GPa.
At 20 degree C, there is a gap d = 0.2 between the lower end of the bronze bar and the rigid slab supported by two steel bars as shown. Neglecting the mass of the slab, determine the stress in each rod when the temperature assembly is increased to 100 degree C. *DRAW THE FBD; complete solution *use 3 decimals
A steel rod with a cross sectional area of 120〖mm〗^2 is stretched between two fixed points. The tensile load at 20°C is 4200N. What will be the stress at-25°C? α=11.7x〖10〗^(-6)/°C and E = 200GPa. See figure 06
Two steel tubes are joined at B by four pins (dp = 11 mm), as shown in the cross section a – a in the figure. The outer diameters of the tubes are dAB = 40 mm and dBC = 28 mm. The wall thicknesses are tAB = 6 mm and tBC = 7 mm. The yield stress in tension for the steel is (y = 200 MPa and the ultimate stress in tension is (U = 340 MPa. The corresponding yield and ultimate values in shear of the pine are 80 MPa and 140 MPa, respectively. Finally, the yield and ultimate values in bearing between the pins and the tubes are 260 MPa and 450 MPa, respectively. Assume that the factors of safety with respect to yield stress and ultimate stress are 4 and 5, respectively.Calculate the allowable tensile force Pallow considering tension in the tubes.Recompute the Pallow for shear in the pins.Finally, recompute Pallow for bearing between the pins and the tubes. What is the controlling value of P?
A steel rod of 20mm is enclosed centrally in a hollow copper tube of external diameter 40mm and internal diameter of 35mm the composite bar is then subjected to an axial pull of 50KN.If the length of each bar is equal to 200mm,determine 1.The stress in the rod and the tube 2.Load carried by each bar Take E for steel=200KN/mm2 and copper =100KN/mm2
Strength of materials - ENGR 3321 The answer should be: 17.68 kN; 11.8 MN/m2 compressive