2. An elastic rod of 25mm in diameter, 200mm long extends by 0.25mm under a tensile load of 40KN. Find the intensity of stress, the strain and the elastic modulus for the material of the rod.
Q: 2. An Al alloy rod with 300 mm length and 10 mm in diameter is subjected to 5 x 10° N force at one…
A:
Q: A 115 m long steel cable with a cross-sectional area of 1.13 x 104 m² is subjected to a tensile…
A: Given , Length of the cable , L =115 m Cross sectional area , A = 1.13*10-4 m2. Force acting , P…
Q: A circular solid piece of rock is tested in a compression testing rig to examine its stress/strain…
A: Sample diameter, d=6 inchesSample original length, L=12 inchesCompression load, P=10000 lbfReduction…
Q: Question 3: a. A mass of (Z + 50) kg is hung on a steel wire of diameter (Z + 5) mm and the…
A: We are suppose to solve only one question. Please post other question as a separate question.
Q: B/A steel bar 200 mm long and having a square cross section 40 mm on an edge is pulled in tension…
A: Given data, L= 200 mm Cross section of S= 40 mm So area will be A=S²= 1600 mm² P= 180000 N…
Q: Two round rods, one of steel, the other of brass, are joined end to end. Each rod is 0.5 m long and…
A: Given that, Esteel=20×1010PaEbrass=10×1010Pa
Q: If Young's modulus of some material is 150 GPa and shear modulus is 50 GPa, find the poisson's ratio…
A: Given, Young's modulus = E = 150 GPa Shear modulus = G = 50 GPa Let us consider, Poisson's ratio…
Q: stress 37 ksi- strain in 0.002-
A:
Q: The is a rope that just cannot stretch more than 0.6 cm from a tensile force of 500N without…
A: Given: Tensile force applied on the rope, T=500 N mass of the rope, m=0.5 kg length of the rope,…
Q: A rod subjected tensile stress is 15.92 x 10°N/mm2 and tensile strain is 0.01 then find young…
A:
Q: Calculate the modulus of rigidity and bulk modulus of a cylindrical bar of diameter of 25 mm and of…
A: Relation between the lateral and the longitudinal strain is εl=4εd The poison's ratio is…
Q: Find the tensile stress in the rod having a diameter of 25 mm subjected to a tensile load of 500 N.…
A: Given, Diameter of rod = d = 25 mm Tensile load = P = 500 N Young's modulus = E = 200 GPa = 200 x…
Q: The longitudinal strain in a cylindrical bar of diameter 20mm and length 2.5m during the tensile…
A:
Q: 1. Consider a cylindrical specimen of some hypothetical metal alloy that has a diameter of 10.0 mm.…
A:
Q: A 35 kN axial load is applied to a metal bar with a rectangular cross-section, 28mm wide by 10mm…
A: To find: The original length of the bar. Given: The load is P=35 kN. The width is 28 mm and…
Q: The corner of a 0.4m_0.3m_0.2 m cubic element is displaced to point C, whose coordinates are…
A:
Q: A straight bar of uniform cross sectionis tested in tension. The bar's cross sectional is 6.5 square…
A:
Q: The length of a wire increases from 1.25 m to 1.2508 m when a load of 12 kg is suspended. The radius…
A:
Q: A rubber block with dimensions of 120x120x120 mm is compressed in a rigid mold cavity with a…
A:
Q: Stress strain behavior of a cast iron with a diameter of 15.8mm and gauge length of 60.80mm is shown…
A: Given Stress strain graph L =60.8 mm Diameter 15.8 mm to find Percentage elongation
Q: 3. If the engineering strain in a tensile bar is 0.0025 and Poisson's ratio is 0.33, find the…
A:
Q: 2. A polymer wire has cross sectional area of 6 mm² and is elongated by using sixty kilogram of…
A: Load , W=60kg = 60×9.81=588.6N Area, A= 6mm2 Strain (e) = 10% of 0.6=0.06 Length, L=600cm
Q: Two bars of different materials and same size are subjected to the same tensile force. If the bars…
A:
Q: A rubber block with dimensions of 120x120x120 mm is compressed in a rigid mold cavity with a…
A:
Q: Find the total toughness energy for a metal that experiences both elastic and plastic deformations.…
A: modulus of elasticity = 107.2 GPa neT = 1.66xK K = 1453 MPa N= 0.175 Strain values range from…
Q: Consider a cylindrical nickel wire 1.6 mm in diameter and 3.5 × 104 mm long. Calculate its…
A:
Q: A 8mm diameter rod, of unknown material, is subjected to 50kN tensile load. In the process, its…
A: GIVEN DATA Diameter d=8mm Load P=50KN Initial length =300mm final length = 303mm
Q: Q.1 A 2 m solid steel bar of diameter 100 mm is subjected to a axial tensile load of 100 kN. Find…
A: Given: The diameter of the shaft is, d=100 mm. The length of the steel shaft is, l=2 m. The value…
Q: A rod 200 cm long and of diameter 3.0 cm is subjected to an axial pull of 30 kN. If the Young’s…
A:
Q: A copper wire of 1mm diameter and 20cm in length is stretched by 0.1cm by applying a force of…
A: Since you have asked multiple parts in a single request, we would be answering only the first three…
Q: If the length and diameter of a material is 25 cm and 10 mm respectively. Then find the elongation…
A: Given : load, W =750*103N length, L=250mm diameter,d =10mm Area,A =π/4*d2 =78.53 mm2 young modulus ,…
Q: A rod is subjected to a uni-axial load within linear elastic limit. When the change in the stress is…
A: Given data: The change in the stress is σ = 200 MPa. The change in the stain is ε = 0.001. The…
Q: dimensions. Here, l=30 cm and the diameter is 4 cm. A Calculate the level of the tensile strength…
A: To given that,Pf(v)=0.1Pf(v0)=0.01module,m=9a we know that , P=1-e-(σσ0)m…
Q: After a fall, a 98 kg rock climber finds himself dangling from the end of a rope that had been 17 m…
A: Given:-m=98 kgL=17 mD=9.8mm∆L=3.1cm=0.031mTo find:-a) Strainb) Stressc) Youngs modulus
Q: 1. A rod is subjected to a uni-axial load within linear elastic limit. When the change in the stress…
A: Given, Change in stress = Δσ = 200 MPa = 200 x 106 Pa Change in strain = Δε = 0.001 Poisson ratio =…
Q: A hollow copper pipe undergoes a 1% change in length under a tensile load. If the Young’s modulus of…
A: We have been given the following data:The percentage change in length of the hollow copper pipe,…
Q: A steel bar is stressed to 280MPa.The modulus of elasticity is 205 GPa. The bar is 80mm diameter and…
A:
Q: A rod is subjected to a uniaxial load within linear elastic limit. When the change in the stress is…
A: Given data: The change in stress, σ=200 MPa. The change in strain, ε=0.001. The Poisson's ratio,…
Q: A rectangular steel block is 300mm in the x direction, 200mm in the y direction and 150mm in the z…
A: Given Force. FX = 250 kN FY = 320 kN FZ = 180 kN Find Strain in X…
Q: Derive the expression for the strain transformation.
A: Strain transformation:- Strain-Transformation equations are based on the geometry of the…
Q: Calculate the modulus E and the shear modulus G
A:
Q: a) Calculate the principal strains, given that the state of plane strain for an element is: E =…
A:
Q: A tensile stress is to be applied along the long axis of a cylindrical brass and that has a diameter…
A:
Q: the longitudinal strain is 0.003 and the poisson's ratio is 0.3, calculate the transverse strain.
A:
Q: material is 25 cm and 10 mm respectively. Then find the elongation of the material when it is 50 kN.…
A: Given:Length of member,L=25 cm=0.25mDiameter of member,D=10mm=0.01mLoad on the…
Q: A metal bar 5.0 m long extends by 0.05 m when a load is applied to it. The strain is?
A: Given that, Length of the metal bar, L = 5 m, Change in length of the bar after applying load,…
Q: A rod is subjected to an uni-axial load within linear elastic limit.When the change in the stress…
A:
Q: A rubber block with dimensions of 120x120x120 mm is compressed in a rigid mold cavity with a…
A:
Q: A steel Column is 10m long and Ø1.2m. It carries a load of 102MN. Given the modulus of Elasticity is…
A: Given Length of column 'l'=10mDiameter of column 'ϕ'=1.2mLoad carried of column 'P'=102MN…
Step by step
Solved in 2 steps with 2 images
- A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?A spherical steel pressure vessel (diameter 500 mm, thickness 10 mm) is coated with brittle lacquer that cracks when the strain reaches 150 X 10~ (see figure). (a) What internal pressure p will cause the lacquer to develop cracks? (Assume E = 205 GPa and v = 0.30.) (b) If the strain is measured at 125 x 10-6, what is the internal pressure at that point?A rubber ball (sec figure) is inflated to a pressure of 65 kPa. At that pressure, the diameter of the ball is 240 mm and the wall thickness is 1.25 mm. The rubber has a modulus of elasticity E = 3,7 MPa and Poisson's ratio v = 0.48. (a) Determine the maximum stress and strain in the ball, (b) If the strain must be limited to 0.425, Find the minimum required wall thickness of the ball.
- A hollow copper pipe undergoes a 1% change in length under a tensile load. If the Young’s modulus of copper is 110 GPa, the pipe’s outer diameter is 2 cm and its wall thickness is 5 mm, what is the magnitude of the tensile load? Consider the whole change happening in the elastic region.The length of a wire increases from 1.25 m to 1.2508 m when a load of 12 kg is suspended. The radius of the wire is 0.5 mm. Find the stress, strain and young's modulus of material of the wire. Draw a free body diagram.A rod is subjected to a uni-axial load within linear elastic limit. When the change in the stress is 200 MPa, the change in the strain is 0.001. If the Poisson's ratio of the rod is 0.3, calculate the modulus of rigidity.
- A bar of size 3m long, 250 mm wide and 150 mm thick is subjected to pull of 50 kN. Find change in length, breadth and thickness. E= 2 X 10^5 N/mm^2 , Poisson’s ratio= 0.25. Calculate modulus of rigidity and bulk modulus. Also, find volumetric strain and change in volume.A metal bar 5.0 m long extends by 0.05 mm when a tensile load is applied to it. The percentage strain is:At a point in a bar of cast iron, the principal stresses are 60 MPa tensile and 120 MPa compressive whereas the third principal stress is zero. Find the factorsof safety based on the elastic limit when the criterion of failure is principal stress theory. Assume the elasticlimit of cast iron is 90 MPa in tension and 440 MPa in compression
- a copper-rolled wire 10 m long and 1.5mm in diameter when supporting a weight of 35.7 kg, elongates 1.36 cm. Compute the stress (kg/cm^2), strain, and the value of the Young's modulus of elasticity for this wire.If the engineering strain in a tensile bar is 0.0025 and Poisson’s ratio is 0.33, find the original length and the original diameter if the length and diameter under load are 2.333 ft. and 1.005 in. respectively.Find the final length of the bar of an aluminum alloy with a modulus of elasticity of 68.8 GPa, whose initial length l0 is 1.9 m when a tensile stress of 208.0 MPa is applied.