Two round rods, one of steel, the other of brass, are joined end to end. Each rod is 0.5 m long and 2 cm in diameter. The combination is subjected to a tensile force of 5000 N. Find the strain in each rod. Young's Modulus of Steel use 20×10¹⁰ Pa, of brass use 10×10¹⁰ Pa. Find the elongation of each rod.

Two round rods, one of steel, the other of brass, are joined end to end. Each rod is 0.5 m long and 2 cm in diameter. The combination is subjected to a tensile force of 5000 N. Find the strain in each rod. Young's Modulus of Steel use 20×10¹⁰ Pa, of brass use 10×10¹⁰ Pa. Find the elongation of each rod.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.7.5P: Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight...

See similar textbooks

Similar questions

- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
2.Show that volumetric strain in a bar is equal to the sum of strains in three mutually perpendicular directions. 3. Explain the terms: (i) Modulus of elasticity (ii) Modulus of rigidity and (ii) Bulk modulus. 4. Derive the relationship between (i) Modulus of elasticity and modulus of rigidity (ii) Modulus of elasticity and bulk modulus
A Mild steel rod of 15mm diameter that is 1.5 cm in length is elongated by 0.15mm along its longitudinal direction by a load of 15 kN. Hence, the strain of the material is …………….. mm/mm.
Use the principle of Strain energy due to direct stresses strength of materials 2
The length of a wire increases from 1.25 m to 1.2508 m when a load of 12 kg is suspended. The radius of the wire is 0.5 mm. Find the stress, strain and young's modulus of material of the wire. Draw a free body diagram.
A steel bar is stressed to 280MPa.The modulus of elasticity is 205 GPa. The bar is 80mm diameter and 240 mm long. Determine the following I) the strain 2) the force
If the Young's modulus and Poisson's ratio of the container material are 100 GPa and 0.3 respectively, What is the axial strain in the cylinder wall at mid-depth?
A rod 200 cm long and of diameter 3.0 cm is subjected to an axial pull of 30 kN. If the Young’s modulus of the material of the rod is 2 x 105 N/mm2, Calculate :(i) stress (ii) strain and (iii) the elongation of the rod.
A copper cylinder with a length of 1.5 m and diameter of 4 cm undergoes compression. (refer to the image ) (a) What will be the bulk strain of the copper rod if pressure is applied to reduce its volume to 0.00089 m3? (b) How much pressure was applied to the copper rod? (c) Calculate the percent change in volume of the copper rod.
The bar ABC shown is loaded by a force P1=20 kN and P2= 40 kN at points C and B respectively. The bar has a constant axial rigidity of 120 x 10^6 N. A. Determine the strain energy of the bar when the force P1 acts alone (P2=0)B. Determine the strain energy of the bar when the force P2 acts alone (P1=0)C. Determine the strain energy when the forces P1 and P2 are acting simultaneously upon the bar.
Compound axial member ABC has a uniform diameter of d=1.45 in. Segment (1) is an aluminum [E1=10,000 ksi] alloy rod with a length of L1=88 in. Segment (2) is a copper [E2=17,000 ksi] alloy rod with a length of L2=128 in. When axial force P is applied, a strain gage attached to copper segment (2) measures a normal strain of ε2=2200 μin./in. in the longitudinal direction. What is the total elongation of member ABC? answer is in inches