2. An ideal Diesel cycle has a maximum cycle temperature of 2300°F and a cutoff ratio of 1.4. The state of the air at the beginning of the compression is P1 = 14.4 psia and T;= 50°F. This cycle is executed in a four-stroke, eight-cylinder engine with a cylinder bore of 4 in and a piston stroke of 4 in. The minimum volume enclosed in the cylinder is 4.5%of the maximum cylinder volume. Determine the power produced by this engine in hp when it is operated at 1800 rpm. Use air standard values during the analysis.

2. An ideal Diesel cycle has a maximum cycle temperature of 2300°F and a cutoff ratio of 1.4. The state of the air at the beginning of the compression is P1 = 14.4 psia and T;= 50°F. This cycle is executed in a four-stroke, eight-cylinder engine with a cylinder bore of 4 in and a piston stroke of 4 in. The minimum volume enclosed in the cylinder is 4.5%of the maximum cylinder volume. Determine the power produced by this engine in hp when it is operated at 1800 rpm. Use air standard values during the analysis.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At the beginning of the compression stroke an ideal otto cycle has an ideal pressure of 15 psia. A temperature of 75degF and specific volume of 13.2ft^3/lbm. At the end of compression, the specific volume is 1.76ft^3/lbm. The heat supplied to the cycle is 532BTU/lbm. For the cycle calculate. 1. Compression ratio2. The highest temperature of the cycle. (Rankine) 3. The highest pressure of the cycle. (psia) 4. The temperature at the end of the expansion of the air. (Rankine)5. The pressure at the end lf the expansion of thr air. (psia) 6. Heat rejected. (7. The net work of the cycle. 8. The thermal efficiency of the cycle. 9. The power developed by an ideal engine operating on this cycle using 0.5lb of air per second. (Horse Power)
An air-standard Diesel cycle engine operates as follows: The temperatures at the beginning and end of the compression stroke are 30 °C and 700 °C, respectively. The net work per cycle is 590.1 kJ/kg, and the heat transfer input per cycle is 925 kJ/ kg. Determine the a) compression ratio, b) maximum temperature of the cycle, and c) the cutoff ratio, v3/v2.
6 - In the ideal Diesel cycle, the compression ratio is 20. The initial temperature of the air is 293 K. Given that the specific heats do not change with temperature, which of the following is the temperature at the end of compression? a) 971.1K B) 1161.6K NS) 1069.1K D) 826.7K TO) 774.8K
1-) In an ideal otto cycle with a compression ratio of 9, the starting temperature of the cycle is 17 ° C pressure 100 kPave, 800 kJ / kg heat is given to the air in the cycle. Accordingly, of the cycle; a) Max temperature and pressure? B) Net workic) Thermal efficiency d) Calculate the average effective pressure e) Draw the T-S and P-V diagrams.
An ideal Brayton cycle with regeneration has a pressure ratio of 8. Air enters the compressor at 300 K and the turbine at 1400 K. If the effectiveness of the regenerator is 100 %, determine: a- back work ratio,b- the net work output,c- the thermal efficiency of the cycle, andd- draw the p-v and T-s diagrams.Account for the variation of specific heats with temperature.
1. a. In a diesel cycle the temperature at the beginning of compression is 870C. If r = 14, find the temperature at the end of the compression. (T2 = 761.550C) b. If the temperature at the beginning and end of the expansion are 17950C and 6770C, respectively, what is the thermal efficiency of the cycle? Assume γ = 1.40. (ηth = 59.26%) 2. An air standard diesel cycle has a compression ratio of 16. The pressure at the beginning of the compression stroke is 1 atm and the temperature is 200C. The maximum temperature is 14300C. Determine the thermal efficiency and the mean effective pressure for this cycle. (ηth = 61.79%, MEP = 6.412 atm)
Draw and label the P-V and T-S diagrams. An ideal Diesel cycle has a maximum cycle temperature of 2300°F and a cutoff ratio of 1.4. The state of the air at the beginning of the compression is P1=14.4 psia and T1=50°F. This cycle is executed in a four-stroke, eight-cylinder engine with a cylinder bore of 4 in and a piston stroke of 4 in. The minimum volume enclosed in the cylinder is 4.5 percent of the maximum cylinder volume. Determine the:a. Compression ratio. b. Power produced by this engine when it is operated at 1800 rpm.
At the beginning of the compression process of air-standard Diesel cycle operating with a compression ratio of 18, the temperature is 300 K and the pressure is 0.1 MPa. The cut-off ratio for the cycle is 2 and the mass flow rate in the system is 1900 kg/hr. Cp=1.006 kJ/kg K Cv= 0.717 kJ/kg K 1) calculate the thermal efficiency of the cycle in %? 2) which formula should be used to determine the thermal efficiency of the cycle ?
A diesel Cycle engine with k of 1.33 has an air standard efficiency of 60.5%. The temperature at the end of isentropic compression is 695oC and the maximum pressure of 62 bar. If the energy released during combustion is 710 KJ/Kg of air, and the pressure at the end expansion is 515oC determine • The maximum temperature of the cycle • The temperature at the beginning of compression • The cut off ratio
Draw and label the P-V and T-S diagrams. An ideal Otto cycle has a compression ratio of 10.5, takes in air at 90 kPa and 40°C, and isrepeated 2500 times per minute. Determine the following:a. Thermal efficiency. b. Rate of Heat Input if the cycle is to produce 90 kW of power. 1
An ideal, air-standard Diesel cycle has a compression ratio of 20. The maximum temperature is 2200 K while the air is 320 K and at 105 kPa before compression. Assume that specific heats vary with temperature. 1. Report the temperature after compression in K. 2. Report the cutoff ratio to two decmial places using rounding. 3. Report the amount of heat added to the cycle in kJ/kg to one decimal place using rounding. 4. Report the temperature after isentropic expansion in K to one decimal place using rounding. 5. Report the amount of heat rejected in kJ/kg rounded to one decimal place. 6. Report the net work produced in kJ/kg to the nearest whole number using rounding. 7. Report the overall thermal efficiency as a percentage (0 to 100) to one decimal place using rounding.
An ideal diesel cycle has a compression ratio of 12 and a cutoff ratio of 2. At the beginning of the compression process, the pressure of the air is 100 kPa, its temperature is 300 K and its volume is 1800 cm2. If the compression ratio is increased by 25% and the volume is decreased by 10%, how much will the average effective pressure increase? Solve with cold air standards assumptions (assuming specific heats at room temperature). (Cp: 1.0035 kJ/kgK; cy: 0.7165 kJ/kgK; R: 0.287 kJ/kgK; k: 1.4)