2. At a particular temperature, the surface tension of water is 0.073 N/m. Under ideal conditions, the contact angle between the glass is zero. A student in a laboratory observes water in a glass capillary tube with a diameter of 0.10mm. What is the theoretical height of the capillary rise?

2. At a particular temperature, the surface tension of water is 0.073 N/m. Under ideal conditions, the contact angle between the glass is zero. A student in a laboratory observes water in a glass capillary tube with a diameter of 0.10mm. What is the theoretical height of the capillary rise?

Name: 2. At a particular temperature, the surface tension of water is0.073
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 2. At a particular temperature, the surface tension of water is0.073 N/m. Under ideal conditions, the contact angle betweenthe glass is zero. A student in a laboratory observes water in aglass capillary tube with a diameter of 0.10mm. What is thethe

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Similar questions

A glass tube 5 ft long and 1 inch in diameter with one end closed is inserted vertically with the open end down, into a tank of water until the open end is submerged to a depth of 4 ft. If the barometric pressure is 14.30 lb per sq.in, and neglecting vapor pressure, how high will water rise in the tube?
Assuming specific weight of air to be constant at 12 N/m3, what is the approximate height of a Mountain if mercurybarometer at the base of the mountains reads 645 mm and at the same time another mercury barometer at the top of the mountains reads 480 mm?
pressurea are sometimes determined by measuring the height of a column of liquid in a vertical tube, what diameter clean glass tubing is required so that the rise of the water at 20°C in a tube due to capillary action (as opposed to pressure in tube) is less than h=1.0mm
Pressure in a water container can be measured by an open vertical tube. If the expected water rise is about 20cm. What tube diameter is needed to ensure the capillary action is less than 3%?
assuming specific weight of air to be constant at 12 N/m2 . What is the approximate height of Mt. Kanlaon if a mercury barometer at the base of the mountain reads 654mm Hg and at the same time another barometer at the top of the mountain reads 435 mm Hg?
A tank of water 4 m deep receives a constant upwardacceleration a z . Determine ( a ) the gage pressure at the tankbottom if a z = 5 m 2 /s and ( b ) the value of a z that causes thegage pressure at the tank bottom to be 1 atm.
The pressure and temperature of the vessel is 380 KPa and 60 degrees celcius, what is the density of air in kg/m3? (neat handwritten)
The barometric pressure reading at sea level is 760 mm of mercury while that on top 735 mm. if the density of air is assumed constant at 1.2 kg / (m ^ 3) ,calculate the elevation of the mountain top?
An open cylindrical tank has a base diameter of 1.2 meter and contains 3.86 meter deep water. the tank is rotated about its vertical axis at 80 rpma. What is the maximum height of the tank so that no water will spill at 80 rpm? b. If ω = 140 MPa, what will be the pressure at the center bottom of the tank?
Problem 1 In a manometer, the height of the water is 50 cm on the right leg, and the height of another liquid is 30 cm on the left leg, measured from the bottom of the tube. Draw the figure and determine the density of another liquid?
The water in a tank is pressurized by air, and the pressure is measured by a multi-fluid manometer, as shown in the figure. Determine the gage pressure of air in the tank.
A U-tube manometer is connected to a closed tank as shown. The air pressure in the tank is 0.25 psi and the liquid in the tank is oil (SG=0.6) . The pressure at point A is 1 psi. a. Determine the depth z (in feet) of oil in the tank. b. Determine the differential reading, h (in feet), on the manometer.