2. Calculate the following: a. V₁, V₂, and V3 b. VAG, VBG, and VCG V₁=100v +-+ RT= 100 ohms R2= 180 ohms R3= 220 ohms G A B C

Q: 1. To minimize the effect of the feedback circuit loading in oscillation frequency we we..........…

A: Since there are 4 different questions, as per the guidelines, in the following section, the first…

Q: * What does the MOSFET characteristic VGS(th) refer to? The maximum threshold for the O Gate/Source…

A: We need to select correct option for Threshold voltage for MOSFET .

Q: 3. A 50-Hz, 250-V single-phase power line has the following loads placed across it in parallel : 4…

A: 3) Given : a single phase power line  Loads are connected in parallel across the source To calculate…

Q: Q5. The negative unity feedback system that has the forward transfer functions as s²-8s+15 with…

A: Root Locus: Root locus is the technique used to determine the relative stability of a closed loop…

Q: The unit of the magnetic field intensity is ? O Amperes per millimeter OFlux per meter O Amperes per…

A:

Q: A single-phase full-bridge voltage source inverter, fed from 200 V d.c. source. The output voltage…

A: Full bridge inverter are consist a 4 diode and 4 controller switch. Full bridge inverter is used to…

Q: The potential difference is measured in .volt

A: Potential Difference:

Q: What type of HVDC link is the following configuration? a) Monopolar b) Homopolar c) Bipolar d)…

A: The given HVDC link is shown below:

Q: VDS is + 1 MQ 2 V 16 v 4.75v 24 V 8.1 V + + VGS 916 V • 2 ΚΩ OD S IDSS = 10 mA Vp=-8 V

A:

Q: what the region of operation for the transistor circuit shown when RB=150 kn. The transistor used…

A:

Q: A unit feedback system has open-loop transfer function: 25 G(s) = s(s+6) The peak overshoot in the…

A: Given: A unity feedback system has open loop transfer function, Gs=25ss+6 Hs=1

Q: Capacitance is measured in Ampere. O True O False

A:

Q: The corrected instrument readings obtained from open and short-circuit test on 10- kVA, 450/120-v,…

A: The expression for efficiency is expressed as, Efiiciency, %η = outputoutput + losses   Thus, the…

Q: The charge of an electron is -1.60 x 10-19 C. A current of 3.5 A flows in a wire carried by…

A: Given that I= 3.5A Charge of electron = 1.60*10-19c T= 1sec

Q: Q2) For the circuit in the figure below, calculate the input power, output power, and power handled…

A: Given: A power amplifier circuit.  According to question:  The peak input voltage is calculated…

Q: Find 11 and i 2

A:

Q: calculate 80% response time for the sytem 0.8T+T=8u(t)

A: Given: the system 0.8T+T=8u(t)

Q: - it used to protect against high voltage surges.

A:

Q: The function of zener diode is to provide a constant output voltage to a load. this process is…

A: Zener diode is special purpose diode it can allow to flow current in reversed direction

Q: The integral of the normal component of any vector field over a closed surface is equal to the…

A:

Q: What will be the binary representation of 66 DEC in BCD coding system

A: Given: Decimal number 66

Q: Q91 For the Logic Circuit shown in figure (6) write the SOP logical expression of the function (F)…

A:

Q: Assume that all of the light emitted by a 150W incandescent lamp (2760 lm) luminates a 100ft2…

A: Given data, Luminous flux is given Luminous flux = 2760 lm Surface area A=9.29 m2

Q: What does the MOSFET characteristic VGS(th) refer to? The maximum threshold for the O Gate/Source…

A: We need to select correct option for given statement.

Q: In this type of digital circuit, its output is dependent on the new input. none of the above O…

A: We need to select correct option for given statement

Q: In this circuit and graph, there are three different load lines plotted, representing three…

A: We need select correct option for given circuit

Q: 8.a. What is the purpose of relay CRE in the roll stand machine? A. Relay CRE is used as an…

A: CRE relay is used to detect fault in the input circuit. It is used in stop button of contact welding…

Q: What is the ac current flowing in the circuit shown below? 12 v 1.5kHz 0.1 μF

A:

Q: it used to protect against high voltage surges. Your answer circuit is used to shift vertically of…

A: 1)  Lightning arrestor or surge diverter is used to protect against High voltage surges.

Q: * Calculate the amount of gate-to- source voltage necessary to regulate a JFET's drain current at a…

A: About JFET problem  Asking Gate source voltage. Given data , I D = 2.5 mA , I DSS = 17 mA , V GS…

Q: A) For the certain lossless reciprocal networks with information of [ A-D=3=4) 1) Evaluate the…

A:

Q: (1) List 3 characteristics of an ideal op-amp. (ii) Name 2 basic circuit applications for linear and…

A: NOTE- As per the rules we can answer only sub-parts from the first question part, please post the…

Q: One line voltage of a balanced Y-connected source is VAB = 180-20° V. If the source is connected to…

A: In this question We need to determine the phase and line currents.  We know , current I= V/Z Phase…

Q: 5. Consider a silicon p-n junction with an n-type concentration of 2 x 10¹6 cm-³ and p-type…

A: Semiconductor:-  Materials in which conduction is between conductor and insulator is called…

Q: A 12 m x 8 m classroom with 4 m high ceiling will have an ambient lighting target illuminance of 800…

A: Given information, Length of classroom L=12 m. Width of classroom W=8 m. Height of ceiling HC=4 m.…

Q: here are 6 × 10 small picture elements in a video each having 8 distinguishable 4 equiprobable…

A: The signal to noise ratio is a parameter used in transmission channels to mathematically calculate…

Q: A new bizarre coffee machine has two LED lights, RED and GREEN which light up based on certain…

A: The simplified output expression can be obtained by using the truth table and k-map. The truth table…

Q: Make a logical circuit of the output equation F = A(B+C) and complete the following table based on…

A:

Q: The resistance of a wire with length of 6.7 mile and diameter of 0.5 in and conductivity of 3.20 S/m…

A: Ans (d) none

Q: What does the MOSFET characteristic VGS(th) refer

A:

Q: In a balanced network, AB is a resistance of 500Ω in series with an inductor of 0.18 H, BC  and DA…

A:

Q: a medium is characterized by σ= 0,  μ= 2μ0,, and  ε= 5ε0. if H = 2 cos (wt — 3y) az, a/m, calculate…

A: Given Data, H=2 Cos(ωt−3y)a⏞z A/mσ=0μ= 2μ0∈=5∈0

Q: To convert a given block diagram R- G/2 2H Into a unity feedback system R G₁ G₁ should be-

A: Given block diagram,

Q: e circuit show num output v A

A:

Q: In diode reverse biasing the potential barrier and depletion region will increase. True False The…

A: Given In diode reverse biasing the potential barrier and depletion region will increase.

Q: trasformer has a copper loss of 1.5% and reactance 3.5% when tested on load. Calculate its full load…

A:

Q: For the source-follower of Fig. 5.22, IDSS = 16 mA, Vp = -4 V, RG = 1 MW, Rs = 2.2 kW, VDD = +9 V…

A: We need to find out voltage gain for given circuit

Q: mathematically functioning of - gate is given as Z = X.Y

A:

Q: P4: Find complex Fourier representation of signal f(t)=3+2 cos (wt)+5 sin (2wt) +2 cos (3wt)

A: For the above given sinusoidal signal we need to calculate complex fourier series representation.

Q: Obtain the Thevenin equivalent at terminals a-b of the circuit in the figure shown below. d -j6Ω 4Ω…

A:

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.