Variation of which of the following parameter is not consider as power quality problem for industry? Voltage Current Power Frequency

Q: Q1. This is the FET relationship of a change in Ip to the corresponding change in VGs. a.…

A: In this question, we need to choose the correct option What is the FET relationship of a change in…

Q: f. Apparent power of the circuit g. Power factor of the entire circuit

A: apparent power S = VI*power factor = cos(angle of apparent power)from existing answer,source voltage…

Q: 1. Sketch V. and determine Vac, V ms - 56 k

A: The solution can be achieved as follows.

Q: The noise from a power mower was measured at 103 dB. The noise level at a rock concert was measured…

A:

Q: Q\ Determine frequency response of the system below X(n) y(n)

A:

Q: determine vo

A:

Q: Vz = 8 V, V6 = 0.6 V, V1 = 2 V. Find the average dc voltage of output waveform.

A: These days, all solar panels provide DC power. Electrical current that travels in a single direction…

Q: ASSUME that le=lc mA Ve V. Vc V. Vec V. Vcc

A:

Q: Quality factor is also known as _________ a) Voltage magnification b) Current magnification c)…

A: As in the resonance  condition the voltage across inductor and capacitor is equal to Q times the…

Q: 22.) The figure below shows a series-parallel circuit. Find the magnitude of the total circuit…

A:

Q: 3 10 0 -j20 N Zab 40N Bj20 n 2.

A:

Q: A tuned AM transmitter have 50µH coil and capacitor of Inf. If oscillator is modulated by audio…

A: Given, Coil inductance (L) = 50 uH Capacitance (C) = 1 nF Maximum frequency component of audio…

Q: 4. Two resistors, 25 kN and 75 kN are at room temperature (290 K). For a bandwidth of 80 kHz,…

A:

Q: Which of the following instrument is used for the measurement of harmonics? Voltmeter Harmonic…

A: Choose the correct option:--- Which instrument is used for the measurement of harmonics?

Q: Q2: Given the circuit shown in figure below, Determine the input impedance of the air-core trans…

A:

Q: 4- What is the output voltage in Fig. 12-52a when the input is low? When it is high? 5- In Fig.…

A: Since you have asked multiple questions, we will solve only the first question for you. If you want…

Q: Xcuta and determine Rue

A: Here no common ROC exists. Hence ZT is not possible.

Q: input and output impedance

A:

Q: For  problem in given figure. (a) determine fundamental period of x[n] (b) compute X[k]

A: The fundamental period of x[n] will be 12 sec.

Q: FIR has may have one zero Select one: O True O False

A: Need to find true false

Q: Q4:If you have the massage (5c H) with 2KH, carrier frequency, draw the PSK and ASK signal.

A:

Q: 2.75 The frequency response of a lincar shift-invariant system is H(el") = elu 2+e-j Find an LCCDE…

A: DTFT

Q: i = 100 sin 314t 2n

A:

Q: Determine the noise factor for the noise ratio of 1.8.

A: Given:  Noise ratio = 1.8. We have to find noise factor.

Q: DiscussIO 1. Compare between Phase method and Filter method that are used in SSB modulation.

A: *As per our guidelines we are supposed to answer?️ only one question since all are different…

Q: At unity power factor of load __________the Active power consumption in a transmission line.

A: At unity power factor load

Q: Which of the three configurations, CE, CC, and CB, provides a phase a reversal from input to output?…

A: The solution is given below

Q: Del the volHage voltage and current @ the load using the grd Appiox

A:

Q: 14.The frequency of a note that is one octave higher than a note of 1024 Hz is

A:

Q: circuit diagram of AC to DC using ltspice show Vin and Vout

A:

Q: 2. Determine Vo for Bazk network for the c'lp shoen 20 8v Tdeal vi Z 2KR Vo - 20t

A:

Q: Q/the output power amplifier circuit is 1.5W at 2KHZ and 0.3mW at 20KHZ and the power is In 10 W,…

A: The solution is as follows.

Q: It refers to the mixing of frequencies in a nonlinear device or the use of nonlinear mixing to…

A: In this question we will write about heterodyne....

Q: 42 0 A 21 0 63 Ω 84 0 Be 105 0

A:

Q: Determine Vo

A: The solution can be achieved as follows.

Q: Determine Toz.

A: Given Circuit voltage across the si diode is 0.7 V and Ge diode is 0.3V

Q: Two resistors, 20kΏ and 50kΏ are at 290 K temperature. Calculate for the rms noise voltage having a…

A:

Q: do number 13.5

A:

Q: Question 3 For an electronic device operating at a temperature of 15°C with a bandwidth kHz,…

A:

Q: 2. Determine Voand Sketch output waveform for the clipper network shown. Ge +10 V 3 V OV 1.0 kN -10…

A: The diode is ON when the voltage across anode is more than the cathode voltage. It is known as…

Q: The gain margin of the system will be Img for the polar plot give below. -0.1 Real ) = 0

A:

Q: An impedance coil draws an apparent power factor of 50 volt ampere and as active pwoer of 40 W.…

A:

Q: Write the nonlinear function to find the ω(lowercase omega) that results in an equivalent impedance…

A: write the equivalent resistance about AB,…

Q: (AB +cD) (B +A) > 13 logcc circuit

A: To draw the logic circuit diagram of the given function

Q: + P is Vo 0.8 pf lagging For the circuit shown above, what is the input power factor angle? Assume…

A: Power factor show the relation between the current and voltage in a electrical system. At a ideal…

Q: Determine peak value of frequency response of 2nd order system if damping ratio is 0.4.

A: Given values are =

Q: What is the power factor

A:

Q: EXAMPLE 3.5 A circuit with two resistors in series (100ohm and 200ohm), a two different temperatures…

A: In this question we will find noise voltage and noise power produced at load....

Q: Q\ Determine frequency response of the system below X(n) + y(n) z-1 z-1

A:

Q: oltage ratio that corresponds to 88.57 dB? (s.OT

A: