2. Consider the following operation: Z = AB BC a. Write out the truth table for the given expression. b. Draw and design a logic circuit that implements the given expression using 6 NMOS devices only. Draw the logic gates diagram first. Use 2-input logic gates only. No need to indicate values for the supply voltage and pull-up resistors. (Hint: You need to manipulate and rewrite expression Z using De Morgan's theorem). c. Given a supply voltage of 5V and assuming low states to be OV, redraw the equivalent circuit and label all important voltages when A=5V, B=5V, and C=5V.

2. Consider the following operation: Z = AB BC a. Write out the truth table for the given expression. b. Draw and design a logic circuit that implements the given expression using 6 NMOS devices only. Draw the logic gates diagram first. Use 2-input logic gates only. No need to indicate values for the supply voltage and pull-up resistors. (Hint: You need to manipulate and rewrite expression Z using De Morgan's theorem). c. Given a supply voltage of 5V and assuming low states to be OV, redraw the equivalent circuit and label all important voltages when A=5V, B=5V, and C=5V.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

1. Design a 16 - to - 1 multiplexer using 4- to-1 multiplexer. 2. Using K- Map, simplify the following Boolean expression : Y = Σ (1,3,5,7,9,10,11,13,14,) 3. Build the logic circuit for the following function using Programmable Logic Array (PLA). ?? = ??? + ??? + ??? + ??? ?? = ??? + ??? + ??? + ???
4.1 Investigate if the following Boolean “identity” is correct, or not. If it is not correct, formulate the correct version of the identity (?′?+?)′=?+?′?′. [2]4.2 Use the identities of Boolean algebra to verify the following identity: [4]?(?+?)+??′+??′+?=?+?+?4.3 Consider the logic gate circuit below:a) Formulate the Boolean expression corresponding to the output of the logic circuit diagram above. [2]b) Hence, show that the Boolean expression formulated in part (a) reduces to ??+?. [3]c) Draw the logic gate circuit diagram corresponding to the reduced expression inpart (b) above. 3.1 Let r, s, t denote the statements “Joe is registered for MCI511S”, “Joe will go to the zoo next week”, “Joe is registered for PBT512S”, respectively. Translate the symbolic statement (∼?∨?)→∼? into words. [2]3.2 Write the negation of the statement “If Joe writes the exam, he will go the airport but he will not catch the flight”. [2]3.3 Determine the truth value of the compound statement (?∧∼?)∨∼?, if p…
Draw the logic circuit for the given expression clearly.
Hello Please answer the following question without handwriting thank you ===================================== For the following functions: Simplify Using Karnaugh map then draw the logic gate diagram F(w, x, y, z) = w′z + xz + x′y + wx′z Using Boolean Algebraic manipulations, minimize the following functions to minimum number of literals in sum of products representation. Show your work clearly step by step indicating the used properties of Boolean Algebra: ? = ( ?′ + ?′ + ?′)( ? + ?′)( ? + ?′)( ?′ + ?)
1.Give the Truth table, Boolean expression and logic circuit diagram for an 8 to 1 multiplexer
Assume a three-story hospital is built at Expo Center Karachi, and you are hired to design the logic circuit for the newly installed lift. The lift only stops at Ground, Second, Third Floors. The lift has one button (RUN), that can be turned into Up or Down position. When the switch is turned to the UP position (i.e. R=1), the lift goes upward from the Ground floor (i.e. 0) to the top floor (i.e. 3), and if the switch is turned to the DOWN position (i.e. R=0) it will go downward. Design this synchronous sequential circuit for this up-down counter using the JK-flip- flops. Perform all design steps, including state-diagram, state-table, K-map, minimized expressions and finally, the draw the logic circuit.
2. Give the Truth table, Boolean expression and logic circuit diagram for a 1 to 8 demultiplexer
Draw a block diagram, truth table and logic circuit of 1*16 Demultiplexer and explain its working principle.
The following Boolean function Y=f(A,B,C,D,E) =Em (0,1,2,4,5,6,10,13,14,18,21,22,24,26,29,30). Design the function with minimal logic gates using: (A) Quine-McClusky method (Tabular method) (B) Karnaugh Map Method.
a) Kindly design a Master-slave J-K flip-flop using NAND gates only and state race-around condition, and how it can be eliminated in a Master-slave J-K flipflop? A multiplexer (MUX) also known as data selector, is a logic circuit which allows the digital information from multi-inputs to a single output line(b) Design a 8 to 1 multiplexer by using the four variable function given by F (A, B, C, D) = ∑m = (013489 15) (c) OUR school AIT has lockers in all the campus that she often rent them out to students who needs them, upon graduation they are taken back by the school authorities. Kindly express the process of opening this locker in terms of digital operation.
Q (A, B, C) = A̅ .B̅. C +A̅ .B. C + A .B. C̅ + A.B.C Karnaugh function given in the form Using the mapping method, you can use the simplified function separately in terms of minterms and maxters. obtain. Output functions with AND NOT for minterms and OR for maxters. Install separately with logic doors.
1. Draw the truth table and logic circuit for a half adder. 2. Implement the following Boolean expression using only NAND gates: (A OR B) AND (NOT A OR NOT B)