ONLY #2 I ALREADY ANSWERED #1x = 6y = 8 1. Determine the pressure in the container at a point 20.xy below the water surface, in (a)pounds per square foot gage; (b) pounds per square inch gage; (c) pounds per squarefoot absolute; (d) pounds per square inch absolute.2. Determine the pressure in a vessel of oil (sp gr 0.85) at a point 15.xy feet below thesurface, expressing the answer in the same units as in problem 1.

Given detail- Depth of liquid = 15.68 Specific gravity of oil = 0.85

Answered: 2. Determine the pressure in a vessel…

2. Determine the pressure in a vessel of oil (sp gr 0.85) at a point 15.xy feet below the surface, expressing the answer in the same units as in problem 1.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The air resistance to the motion of a vehicle is something important that engineers investigate. As ...

A: What is the appropriate unit for C_{d} if the preceding equation is to be homogeneous in units?

Q: Calculate the ultimate axial load capacity of spiral column having a diameter of 500mm is reinforced...

A: The axial load ratio is defined as the applied axial load over the design axial load carrying capaci...

Q: A 1.2 m. wide wall footing was constructed on the surface of a silty sand soil. If the bottom of the...

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy...

A: Given data, P = 60 kN E of aluminium = 73 GPa Aluminum rod diameter = 16 mm Aluminum rod length (L...

Q: Evaluate the resisting capacity against axial load due to skin friction on the following conditions....

A: To determine the resisting capacity of pile against axial load (due to skin friction). Given, Size...

Q: Determine the forces in members AB. CG, and DE of the loaded truss. The forces are positive if in te...

Q: The kinetic energy E of a body is proportional to its weight W and the square of its velocity v. A 1...

Q: Bar BC is made of brass which has E = 90 GPa, a = 20 × 10¯6 /°C, and A = 500 mm² Bar ED is made of s...

Q: For the beam shown in the figure, Determine the following unknowns where L1 = 5m, L2 = 3m, and the %...

A: The values and diagram given in the question are as follows: L1=5 m L2=3 m Moment reaction at fixed ...

Q: A car bumper is designed to bring a 1800 kg car to a stop from a speed of 2.23 m/s while deforming 1...

A: Given:- m=1800kg Car stop from 2.23 m/s to zero, while deformation is 150mm Initial velocity u=2.23 ...

Q: cantilever truss carries a concentrated load P shown in the figure below: -1 e = tan (3/4) C nat are...

A: To find: Magnitude of axial forces

Q: Determine the strain energy in a cantilever beam of uniform cross section and length L subjected to ...

A: Given, A cantilever beam, Length = L, Udl = w,

Q: Assume you are an observer standing at a point along a three-lane roadway. AlIl vehicles in lane 1 a...

Q: PROBLEM NO. 2: A 4 BY 4 – IN. WOOD – POST BC IS CONNECTED TO A 1 - IN. DIAMETER STEEL EYE – BAR AB T...

A: Given data : W=7000 lbs AC=7 inch CD=5 inch BD=5 inch

Q: A rectangular channel carries a discharge of 2 m3/s per meter width if the loss of energy if 2.75 de...

A: Given: The discharge per meter width is 2 m3/sec. The energy loss is 2.75.

Q: A submersible pump is pumping water from a well that is 200 ft of water through a 4 inch PVC pipe. T...

Q: Find the depth of the borehole required for the site investigation in which a circular footing of 3 ...

A: d- 3m Df - 2m P -1560 kN WT depth - 1.5m γd- 17 kN/m3 γsat- 19 kN/m3 To find the Depth of borehole ...

Q: PROBLEM NO. 1: MEMBER GF OF THE PIN – CONNECTED TRUSS IN FIG. 1 HAS A CROSS - SECTIONAL AREA OF 1548...

Q: Concrete sample B142 cylinder 2 had an average diameter of 101.0mm and an average height of 183.31mm...

Q: A sample of dry sand is subjected to a triaxial test . The angle of internal friction is 36° . If th...

A: Given data, A dry sand sample, Angle of internal friction= 30° Cell pressure= σc= σ3= 180kN/m² Fin...

Q: Calculate the support reaction forces for the above beams. Draw shear and moment diagrams.

A: *Multiple questions* As per our guidelines we are supposed to answer?️ only one question. Kindly rep...

Q: 25 kN w A В Using any method shown in class, determine the shear force and bending moment diagram fo...

Q: 0.1. Determine the components of reaction at support A and Reaction at support B. See Figure QI. PKa...

Q: Chapter 2, Problem 2/088 An exhaust system for a pickup truck is shown in the figure. The weights Wh...

A: Given Data: The weight of the head-pipe is Wh=12 N The weight of the muffler is Wm=98 N The weight o...

Q: Determine the tractive effort developed by the engine given the following data: Wheel load = 6 tonne...

Q: Assume straight line instead of parabola for stress strain curve of concrete as follows and partial ...

Q: member. (a) Dctermine the coordinates yR and Za of the point where the tensile load P must act in or...

A: Please find the answer in the below attachments

Q: A simple curve has a central angle of 35°. The offset distance from the PT to the tangent line passi...

A: Given data, Central angle = 35° Tangent line = 75 m To find out the degree of curve.

Q: 53. Prestressed concrete structures showing visible signs of distress in the form of, A. O Surface c...

Q: Assume you are observing traffic in a single lane of a highway at a specific location. You measure t...

Q: *7-32. The double T-beam is fabricated by welding the three plates together as shown. Determine the ...

A: The given values are as follows,For T beam the shear force (V)=80kNTo Determine The shear stressi th...

Q: Create an LOWER TRIANGULAR MATRIX using ROW operations. Show each step and the formulas used. Then, ...

Q: Problem II. A proposed elevated tank for a certain community has a diameter of 72 inches and a heigh...

Q: A materials supplier presented the following values for a sample of their CBR tests for subgrade soi...

A: Here we need to find out the mean absolute deviation of the given CBR results. Mean absolute deviati...

Q: - One of the testing equipments used for inspection is?

A: To find: Which is testing equipment used for inspection.

Q: A reinforced concrete column 200mm in diamter is designed to carry an axial load of 400 kN compressi...

A: Given data, Ec = 14 GPa Es = 200 GPa Axial load (P) = 400 kN Allowable stress in concrete = 6MPa Al...

Q: Derive the following relations for the the limit state design of balanced rectangular RCC beam (a) D...

A: Given data, Fy of steel = 415 MPa E of steel = 2x10^5 To derive following relations for limit state...

Q: A two-storey apartment building designed by Engr. Sang Woo has a brace system of main structural mem...

Q: 52. Which type of inspection is more intensive involving examination of structural elements? A. O Mi...

A: Which method of inspection is more thorough when it comes to structural elements?

Q: A system of forces which produces zero moment: a. parallel forces b. space forces C. concurrent forc...

A: Given various system of forces are given. Parallel forces Space forces Concurrent forces General fo...

Q: Chapter 2, Problem 2/088 An exhaust system for a pickup truck is shown in the figure. The weights Wh...

Q: A two-storey apartment building designed by Engr. Sang Woo has a brace system of main structural mem...

Q: River are shown in Table below. Calculate the average surface rainfall using the methods of arithmet...

Q: Find a diameter of pipe required to carry a design flow of 0.186 m3/s when flowing partially, d/D= 0...

A: Pipe diameter:

Q: If A is 8% taller than B, while B is 9% taller than C, by how much in percent is A taller than C? Se...

A: given A is 8% taller than B B is 9% taller than C It means A=1.08 B B = 1.09 C

Q: Explain why data should always be entered directly into the field book at the time measurements are ...

A: The notes and readings of surveying are recorded in the field book.

Q: For the pipe network shown below, Problem 4(- f=0.022 for all pipes. Determine the discharge in line...

Q: A ball is thrown from the top of a building with an initial velocity of 20:0 m=s straight upward ,at...

A: Using the kinematics equation with proper sign convention the value of T= time taken can be calculat...

Q: A trunk of a car has a listed luggage capacity of 18 ft3 . Express the capacity in in3 , m3 , and cm...

A: Given: The luggage capacity is 18 ft3.

Q: Q1. Determine the components of reaction at support A and Reaction at support B. See Figure QI. PKn ...

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

ONLY #2 I ALREADY ANSWERED #1

x = 6

y = 8

1. Determine the pressure in the container at a point 20.xy below the water surface, in (a)
pounds per square foot gage; (b) pounds per square inch gage; (c) pounds per square
foot absolute; (d) pounds per square inch absolute.
2. Determine the pressure in a vessel of oil (sp gr 0.85) at a point 15.xy feet below the
surface, expressing the answer in the same units as in problem 1.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids—castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT (Illustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z=20ft. a. The hydrostatic force due to linseed oil F1. b. The hydrostatic force due to castor oil F2. c. The hydrostatic force due to water. d. The net hydrostatic force acting on the gate Fnet
For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids—castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT (Illustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z=20ft. A.) The hydrostatic force due to linseed oil F1. B.)The hydrostatic force due to castor oil F2. C.)The hydrostatic force due to water. D.)The net hydrostatic force acting on the gate Fnet
A pressure gage 8m above the bottom of the tank containing a liquid with sg=0.75 reads 120kPa. Another gage height 3m reads 150kPa. Determine the weight density of the liquid
QUESTION 2 Water with sp.gr 0.97 flows through a pipe of uniform diameter 350mm with a mean velocity of 1.0 m/s. Determine the volume flow rate and mass flow rate of water through the pipe. Determine the type of flow based on the Reynolds number “Re”. The pressure at the datum of the pipe is measured as 25 N/cm2 with a pressure gauge. Determine the total head of water at three different locations 1) at the bottom 2) at a height of 5m and 3) at a section which is 10m above the datum. Assume that the pipe is 45 degrees to the horizontal and there are no frictional losses.
water flows out of a pressurized tank through a smooth pipe with Q = 50 m³ / h. In this problem we will find out how big the pressure p1 must be to produce this volume flow? a) What assumptions and simplifications must be made? b) Find the pressure p1. c) Find the same pressure, but using Bernoulli's equation. Comment, what is the difference?
For a vertical rectangular gate, one side has linseed oil (0.939) and the other has two fluids - castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT. Illustrate and label the pressure diagram/prism to calculate the magnitude and direction of the following when z = 20ft. A. The hydrostatic force due to linseed oil F1 B. The hydrostatic force due to castor oil F2 C. The net hydrostatic force acting on the gate Fnet D. The hydrostatic due to water
4.) A 75 mm diameter pipe, 2 m long is just filled with oil (sp. gr. = 0.822) and then capped, and place on horizontal position. It is rotated at 27.5 rad/sec about a vertical axis 0.5 m from one end (outside the pipe). What is the pressure in kPa at the far end of the pipe? Answer: 1865 Kpa Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flow
No wrong answer please. A closed tank 3m in diameter and 3m high is filled with water and rotates about its axis at 100 rpm. A pressure gage at the center of the top reasds 30 kPa. During the rotation. (a) Determine the equivalent height of the fluid above the topalong its periphery. (b) Determine the pressure at the outer perimeter at the bottom of the tank. (b) Determine the pressure at the bottom of the tank at the center.
A venturi meter with a throat diameter of 100 mm is fitted in a vertical pipeline of 200 mm diameter with oil of specific gravity 0.88 flowing upwards. Two pressure gauges are fitted at tapping points, one at the throat and the other in the inlet pipe 320 mm below the throat. The difference between the 2 gage pressure readings is 28 kPa. (a) Determine the flow in m^3/s neglecting head losses (b) Working from Bernoulli's equation, determine the difference in levels (in mm) between the two limbs of a mercury manometer if it is connected to the tapping points and the connecting pipes are filled with the same oil Draw illustrations Use 3 decimals
1. Determine the flow rate in cfs 2. Determine the pressure at point D in psi 3. Determine the velocity at the pipe with 18 inches diameter in ft/s 4. Determine the velocity at the pipe with 8 inches diameter in ft/s
1. An orifice in the side of a vertical tank discharges oil (sp. gr. = 0.82) under a head of 4.0 m. and 25 KPa pressure acting on the surface of the oil. If the diameter of the orifice is 5 cm, the coefficient of contraction is 0.62, and the head lost on the orifice is 45 cm, determine the discharge, coefficient of velocity, and the coefficient of discharge.
An open tube is attached to a tank as shown. A). If Liquid X (Oil SG=0.55) rises to a height of 800 mm in the tube, what is the pressure Pa (in kPa) of the air above water? Neglect capillary effects in the tube. B). If Liquid X (Alcohol SG=0.79) rises to a height of 800 mm in the tube, what is the pressure Pb (in kPa) of the air above water? Neglect capillary effects in the tube.