member. (a) Dctermine the coordinates yR and Za of the point where the tensile load P must act in order to produce uniform tensile stress in the crosS soction of the structural angle, and (b) determine the magnitude of that tensile stress it P- 18 kips. (a) 1.5 in. End plate 4 in 0.5 in 3 in- P2.2-3

member. (a) Dctermine the coordinates yR and Za of the point where the tensile load P must act in order to produce uniform tensile stress in the crosS soction of the structural angle, and (b) determine the magnitude of that tensile stress it P- 18 kips. (a) 1.5 in. End plate 4 in 0.5 in 3 in- P2.2-3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A truss member 8.00 m long carries a compressive load of 200 kN dead and 400 kN live and consists of two C200x17 channels and a 250x10 mm cover plates placed as shown in Fig P207. Check the adequacy of the section.
The pin at C is supported in a single shear connection. If the allowable shear stress is 90 MPa, compute the minimum diameter required for the pin at C
The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in the position shown. Member BD is 5/8 in. thick and is connected to the vertical rod by a 3/8-in.-diameter bolt. Determine (a) the average shearing stress in the bolt, (b) the bearing stress at C in member BD.
The rigid beam is supported by a pin at A and wires BD and CE. If the load P on thebeam causes the end C to be displaced 15 mm downward, determineA. the normal strain developed in wire CEB. the normal strain developed in wires BD.
The members of the structure in Fig. 1 weight 150 lb/ft. Determine the smallest diameter pin that can be used at C if the shearing stress is limited to 4000 psi. Assume single shear
The wall hanger has a thickness of 0.25 in. and is used to support the vertical reactions of the beam that is loaded as shown. If the load is transferred uniformly to each strap of the hanger, determine the state of stress at points C and D on the strap at A. Assume the vertical reaction F at this end acts inthe center and on the edge of the bracket as shown.
Look for Reactions at the support
A 6.5m long cantilever beam 300mm x 600mm carries a uniformly distributed dead load(beam weight included) of 5kN/m throughout the length and a concentrated live load of 19KN at the free end. To prevent excessive deflection of the beam it is pretensioned with 12mm diameter strands causing a final prestress force of 550 KN. Pe= 0.85Pi 3. Determine the eccentricity of the prestress force at the fixed end such that the resulting stress at the top fiber of the beam at the fixed end is zero a. 213.84 mm b. 114.98mm c. 316.13mm d. 284.98mm e. None
The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 9 kN, determine the magnitudes of the average normal stress in the shank, the average shear stress along the cylindrical area of the plate defined by the section lines a–a,and the average shear stress in the bolt head along the cylindrical area defined by the section lines b–b. Answers should be in MPa.
The compound shaft is attached to a rigid wall at each end. a = 2 m and b = 1.5 m. For the bronze segment AB, the diameter is 82 mm and G = 35 GPa. For the steel segment BC, the diameter is 62 mm and G = 83 GPa. The maximum shear stress is limited to 50 MPa in the bronze and 60 MPa in the steel. Compute the largest torque in kN-m that can be applied considering the maximum shear stress of the bronze segment. Compute the largest torque in kN-m that can be applied considering the maximum shear stress of the bronze segment. Compute the largest torque in kN-m that can be applied to the compound shaft. Choose from the choices given above.
The bars of the truss each have a cross-sectional area of 1.15 in2. If the maximum average normal stress in any bar is not to exceed 18 ksi, determine the maximum magnitude P of the loads that can be applied to the truss.
A simply supported girder spans 10 m. It carries two beams each at 3.5 m from the supports. The concentrated load from each beam is 70 kN. A. Calculate the maximum web shear stress in MPa B. Calculate the maximum flexural/bending stress in MPa. C. Calculate the maximum shear stress at neutral axis