2. Discuss the advantages and disadvantages of hydraulic control system with respect to pneumatics contro system.

Q: The composite shaft shown in the figure consists of a bronze sleeve (1) securely bonded to an inner ...

A:

Q: A polymer cylinder (2) is clamped between rigid heads by two steel bolts (1). The steel [E - 29,000 ...

A: Given DataEs=29000ksiEP=370ksiαs=6.5×10-6/°Fαp=39.9×10-6/°FLP=27inLb=35in∆T=145°F

Q: 24- The two stroke cycle engine has: a) one suction valve and one exhaust valve operated by one cam ...

A:

Q: The force moment about O is 500 N 2 m O 400 Nm O 600 Nm O 700 Nm

A: Solution is attached below: 

Q: of the assembly shown. Knowing that a pin of 20 mm diameter is used at each connection, determine 2 ...

A:

Q: hydrastatic force , hydrostatic force 5 to keep the gate in The deneity of (e-?) vertical poation le...

A: Density, ρ1= 1500 kg/m3 Hinge point is at 2 m from the surface of the liquid 1. Let it be represente...

Q: 22- In a four-stroke cycle petrol engine, during suction stroke: a) only air is sucked in b) only pe...

A:

Q: Q4: B: Explain in detail the grinding operations?

A: Grinding is an abrasive machining process that uses a grinder or the grinding wheel as the cutting t...

Q: Q5: Find the both moments of inertia (Ix, Iy) by integration around the central coordinates as shown...

A:

Q: Water flows through a tube of diameter 30 mm at an average velocity of 1.5 m/s. The properties of wa...

A: As given in question, Diameter of the tube = d = 30 mm = 0.03 m Velocity of water = v = 1.5 m/s Prop...

Q: Stress is directly proportional to strain within the proportional limit is Boy's Law 2 Hooke's Law M...

A: Relation between stress and strain is given by Hooke's law. According to that law, Stress in the bod...

Q: HiW. Find the deflection distribution dingram for the followsing laaded beam.

A: The beam is as shown below, RA=RB=5 N,

Q: 19- In a two-stroke cycle engine, the operations namely suction, compression, expansion and exhaust ...

A: 19) In a two stroke cycle engine, the operation namely suction, compression expansion and exhausted ...

Q: 10- In a four stroke cycle petrol engine, the inlet valve a) opens at top dead centre and closes at ...

A: This question is based on the concept of ignition engine 

Q: 2. Knowing that a = 40°, determine the resultant of the three forces shown. 120 lb 20

A:

Q: Water flows through a tube of diameter 30 mm at an average velocity of 1.5 m/s. The properties of wa...

A:

Q: You are asked to design a four cylinder four-stroke spark ignition engine for a passenger car, which...

A:

Q: Note: Solve the problem as stated below. Draw the FBD. PROBLEMS Figure: 1. In the figure shown, a ve...

A:

Q: Draw the schematic diagram for regenerative vapour power cycle with 2 steam blades. Represent the co...

A: Sketching the regenerative vapor power cycle with 2 steam blades.

Q: Air is heated at constant pressure from 27 C to 57 C at 3 bar in a heater from an infinite heat sour...

A: given; temperature (T1)=270c                         =300Ktemperature(T2)=570c                      ...

Q: Q5: Find the both moments of inertia (Ix, ly) by integration around the central coordinates as shown...

A:

Q: SS 304 steel shaft is 3 m long and has an outer diameter of 60 mm. When it is rotating at 60 rad/s, ...

A:

Q: late the machining time to drill the flange as shown below. Take cutting speed 20 m/min, feed for 20...

A: Soln:- depth = 20 mm            Number of Revolution required = depth/feed = 20/ 0.2 = 100 rev. V= π...

Q: Question 3. Displacements at the ends of a two-node axial element at nodes and K 4=0.lcm ve u, = 0.3...

A:

Q: ticle P starts from rest at point A at time t = 0 and changes its speed thereafter tal path shown. D...

A: to given that at=1.9.ga   The magnitude and direction-a=an2-at2   =02-(1.9×9.81)2=18.636m/s2θ=cos-1a...

Q: The bar ABC shown is loaded by a force P1=20 kN and P2= 40 kN at points C and B respectively. The ba...

A: The energy accumulated in a body owing to deformation is known as strain energy. Strain energy densi...

Q: The composite shaft shown in the figure consists of a bronze sleeve (1) securely bonded to an inner ...

A: Answer: (a) The maximum shear stress in ◆ Bronze sleeve (1) : 71.7676 MPa ◆ Steel Core (2) : 95.5348...

Q: The gearing arrangement suitable for this

A: Given; A 2.7 motor is running at 1850 rev/min Power,P=2.7 kW Running at, N=1850 rev/minIt is to be c...

Q: Find the moment about point 0 in figure 2 25 N 45 as 6.5 0.5m 0.5m 2.25 m 40N 20 N 2.75 m 2 m 30 1.5...

A:

Q: 12 mm PROBLEM 1.25 For the assembly and loading of Prob. 1.9, determine (a) the average shearing str...

A:

Q: B: Find the total moment of force with respect to point (A), for the two forces in next fig. 8m 3m 5...

A:

Q: Air is compressed isentropically such that its pressure is increased by 50%. The initial temperature...

A:

Q: The uniform box shown in next figure, has a mass of 40 Kg. If the two forces T = 60 N and F =30 N ar...

A:

Q: 17- Stirling engine can be called as: a) internal combustion engine b) external combustion engine c)...

A: 17. stirling engine can be called as                        option (b) external combustion engine   ...

Q: The v-component of the force is about 30 lb 15 30 O 20.20 Ib O 21.21 lb O 23.23 lb O 24.24 lb

A: Given data as per question Applied force =30 lb considering vector diagram

Q: The uniform box shown in next figure, has a mass of 40 Kg. If the two forces T = 60 N and F=30 N are...

A: Given Data: Mass of the box, m=40 kg Coefficient of static friction, u=0.24

Q: The (180 N) force is applied to the end of body OAB. If 0=50 determined the equivalent force couple ...

A: Given DataF=180Nθ=50°

Q: 1. Collar A moves in a constant velocity of 900 mm/s to the right. At the instant when e = 30°, dete...

A:

Q: 3. If w-30 kN/m and L=10m, the cross section is made-up of two I-beams shown, determine the followin...

A: The greatest bowing second happens in a pillar, when the shear force at that segment is zero or chan...

Q: Reynolds number, based on the pipe diameter

A: Given; Two pipes of uniform section but different diameters carry water at the same flow rate.Water ...

Q: required punch diameter ?

A: Given; Diameter  of the meatal disc is, d= 50 mmThickness, t= 5 mmPunch and the diameter clearance i...

Q: A rigid bar ABC is pinned at A and supported by the cables at point B as shown in the figure. The ro...

A:

Q: 14 K. Calculate the work done by the gas.

A: To find Work done by the gas

Q: SIVERSITY CO KIVERSITY 2 KN 6 kN The magnitude of the resultant force is about 8.675 N 6.765 N 5.567...

A: Resultant of two force is given by the following formula, R=[F1^2+F2^2+2*F1*F2Cos(theta)]^1/2 Where ...

Q: Give example of a problem solved using reheat rankine cycle method and compare to rankine cycle meth...

A: The calculation process is given below: 

Q: Consider laminar flow of water over a flat plate of length 1 m. If the boundary layer thickness at a...

A: Given  dataδ1=8mmx1=0.25mx2=0.75ml=1mδ2=?

Q: Q4 Find the moment about point O in figure 2. 725N 0.5 2.25 m 20 N 2.75 m 2 m 15m 3 m 30 20N

A:

Q: Determine the flow rate of air through an axial bush seal. The outer diameter of the inner cylinder ...

A: Given data: The outer dia. of the inner cylinder is Do = 250 mm = 0.25 m The radial clearance is c =...

Q: e mechanism shown in Figure P8.1 mass of 3.0 lbm and polar mass m tia of 0.04 lb-in-sec2 about its m...

A:               T is torque because of moment of inertia and it acts upper direction and rotate in clo...

Q: 57 C at 3 bar in a heater from an infinite eat source at temperature 227°C. Find the ain in availabi...

A:

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.