2. Find the Force reading on the spring scale. Show all your work and box the answers. Step 1 is to draw a Free Body Diagram and Step 2 is to sum the Forces in the X & Y. Use the diagram included. N is the Normal Force, Tis the Tension and W is the Weight. Spring Scale T 100 ib 20° W N

2. Find the Force reading on the spring scale. Show all your work and box the answers. Step 1 is to draw a Free Body Diagram and Step 2 is to sum the Forces in the X & Y. Use the diagram included. N is the Normal Force, Tis the Tension and W is the Weight. Spring Scale T 100 ib 20° W N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.62P: The bar ABC is supported by three identical, ideal springs. Note that the springs are always...

See similar textbooks

Similar questions

Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
Determine the force in each member of the truss shown in (Figure 1). State if the members are in tension or compression. Take that P = 420 lb. Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression. Given: angle to use is 36.9 degrees, FCD = 700lb FAD =-560lb Find: a) Determine the force in the member BC of the truss, and state if the member is in tension or compression. b) Determine the force in the member AC of the truss, and state if the member is in tension or compression. c) Determine the force in the member AB of the truss, and state if the member is in tension or compression.
Find the forces (F1,F2,F3 lb) in Fig. 364. (A=27, B=64, C=44) deg, (D=4, E=3, F=4) ft, F4=5440 lb If F4 is negative, then the direction of F4 is down. A negative answer indicates that the direction is reversed. Answers can be checked by demonstrating that components balance.
1. This arm is attached to a wall on the left. The right end is free hanging. Each section is 1.9m wide and 3.6m high. If the force at the end of the arm is F = 170.0N, what is the force in member 2? Use a positive number if it is in tension and a negative number if it is in compression. 2. This arm is attached to a wall on the left. The right end is free hanging. Each section is 1.2m wide and 3.0m high. If the force at the end of the arm is F = 150.0N, what is the force in member 9? Use a positive number if it is in tension and a negative number if it is in compression.
A load of W = 34 kN is lifted through a boom 'BCD' as shown in the figure. The boom makes an angle of 60 degrees with the vertical. Neglect the weight of the boom for this problem, L1 = L2 = 2.6 m. The pulley at 'D' is frictionless. a.) Determine the angle ‘α’ in degrees. b.) What is the tension in cable 'AC' in kN? c.) What is the horizontal component at 'B' in kN? *Round off final answer in 4 decimal places. Thank you very much.
A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged such that one end is on the ground and the other against a vertical wall. The angle of triction at all contact surtaces is 20 degrees. What is the value of the coefficient of triction? What is f, in terms of variable Na? What is the normal force at A in terms of variable W? Answer in three decimal places
Physics Use the figure to determine the tension (inpounds) in each cable supporting the load.
2. Forces (Figures Needed) 2.2. A load of 100 lbf hung from the middle of a rope, which is stretched between tworigid walls 30ft apart. Due to the load, the rope sags 4ft in the middle. Determinethe tension in the rope. 1 Free-body Diagram only
a. When load P is applied at room temperature what will be the tension in wire at C and D? [solve for a value in kN] b. When load P is already applied and the room temperature is raised by 30 degrees Celsius, what will be the tensions in the wire at C and the wire at D? [solve for a value in kN] c. What additional temperature rise is required to make the wires at C and D slack(i.e. have zero force)? [in degree Celsius]
Physics for Engineering A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0, respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the left end where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) and the weight (W) of the bar. (Hint: Formulate three equations for the three unknowns, 2 equations for the 1st condition and 1 equation for the 2nd condition.)
P1=215 N P2=325 N P3=150 N L1=3m L2=4m 1. Draw a "free body diagram". The diagram should be for members BE, BF, CF, and DF to help solve. 2. What is the force on members CF, BF, BE? Is each of these members having tension or compression?
Hi! Hope you can help me with this. F1 = 500kN F2 = 600kN Find the force member in CD, BD, AB, BC. Indicate if Tension or Compression