2. Five dry cells, each of which has an internal resistance and emf's of 0.05 ohm and 1.5 volts respectively, have the positive sides all connected together and all negative sides all connected together. Calculate(a) current to a load whose resistance is 4 ohms, (b) terminal voltage of the cells, (c) power lost in each cell, (d) power delivered to the load

2. Five dry cells, each of which has an internal resistance and emf's of 0.05 ohm and 1.5 volts respectively, have the positive sides all connected together and all negative sides all connected together. Calculate(a) current to a load whose resistance is 4 ohms, (b) terminal voltage of the cells, (c) power lost in each cell, (d) power delivered to the load

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter8: Combination Circuits

Section: Chapter Questions

Problem 4PA: The hot water for the heating system for a small factory is supplied by a single boiler. The bolier...

See similar textbooks

Similar questions

The hot water for the heating system for a small factory is supplied by a single boiler. The bolier is locatd in a small building separate form the factory. The power supplied to the bioler is 240-volt single-phase without a netural conductor. At the present time, the small building housing the bioler has no inside lighting. The business owner desires that four 100-watt lamps be installed inside the building. All lamps are to be connected to a single switch. The lamps are to be connected to the present 240-volt sercvice inside the building. How would you accomplish this task? Explain your answer.
A patient is lying in their hospital bed, which is grounded to the room’s ground bus bar. The patient has their left arm on the right metal rail of the bed and reaches for the nurse call button which is having a ground fault. Relative to the room ground, the button is at 120V. The plastic cap on the provides 10kΩ of resistance, while the patient provides 100kΩ. How much current flows through the patient? What is the effect of this current?
2. Imagine that you're asked to install an auxiliary grounding electrode at the base of a lighting pole in aparking lot. This auxiliary grounding electrode will be connected to theA. lighting pole's electrical service equipment grounding conductor.B. electrical service's grounding electrode conductor.C. next lighting pole's auxiliary grounding electrode.D. lighting pole's neutral conductor.
1. A 12-ohm resistor is connected in parallel with a series combination of 8-ohmand 16-ohm resistors. If the voltage across the 8-ohm resistor is 48-volts,calculate the (a) total resistance, (b) total supply voltage, and (c) circuit current.2. A 45-ohm resistor is connected in series with a resistor R whose ohmic value isunknown. If the total current (taken by both resistors) is 7-amperes and thesupply voltage is 120-volts. Calculate the resistance R of the unknown.
In an outdoor substation the three bus-bar conductors are supported by units of post type insulators. Each unit consists of a stack of 3 pin type insulators fixed one on the top of the other. The voltage across the lowest insulator is 15kV and that across the next unit is 12kV. Estimate: i. ratio of mutual to self-capacitance ii. the bus-bar voltage of the substation. iii. Efficiency across the string of insulators
Two resistive loads, A and B, taking 60A and 20A respectively, are connected to a 900m long two-wire radial distributor at distances of 350m and 500m respectively from the feeding point, the supplied voltage at which is 230V. The resistance of the distributor is 0.025Ω per 100m of single conductor. Find: The voltage supplied to each load (A and B) The power consumed by each load and the power loss across each section of the line.
1)For a new construction, a concrete-encased electrode is always required to be used in the grounding electrode system. a) True b) False 2)Soil resistivity is measured to determine the type of soil conditions, the corrosive effects in the soil, and the gest type of grounding electrode system to install. a) Trueb) False
The two small-appliance branch circuits required for the kitchen and dining room area are intended to supply ____ appliances. A. under 1/3 horsepower B. portable C. fixed-in-place D. all
Consider Two same size series connected PV modules,each with the specification as Po=100W, Voc= 24.5V and Isc=5A.then choose the correct Statement Refer to this PV Panel. a.The output power from this panel is 100W , the Voltage is 24.5V and the current is 10A b.The output power from this panel is 200W , the Voltage is 24.5V and the current is 10A c.The output power from this panel is 200W , the Voltage is 49V and the current is 5A d.The output power from this panel is 200W , the Voltage is 49V and the current is 10AClear my choice
1.A. You've assembled the following components to join two copper conductors: a mould, powdered copperoxide, powdered aluminum, and an igniter. With these components, which of the following processes willyou use to connect the conductors?A. Exothermic weldingB. Irreversible compression groundingC. Mechanical groundingD. Thermal cycling 1.B. Two electricians are discussing voltage ratings. Electrician A says that a motor that's installed 40 feetfrom a power source will show a lower applied voltage than a motor that's installed 20 feet from the samepower source. Electrician B says that an exact voltage of 240 V must be applied to a motor that's rated at240 V. Who is correct?A. Neither Electrician A nor Electrician B is correct.B. Only Electrician A is correct.C. Only Electrician B is correct.D. Both Electrician A and Electrician B are correct.
A 125-volt d-c generator whose internal resistance is 0.15 ohm is connected through a 0.45 ohm line resistor to charge two 90-volts storage batteries A and B in parallel. If the internal resistance of batteries A and B, respectively, 0.32 ohm and 0.4 ohm, what are the charging currents?
a.1. A main bonding jumper must only be foundA. within enclosures serving as sub-panels.B. at the grounding electrode.C. on the load side of a GFCI.D. within the enclosure that houses the service disconnecting device.a.2. Which of the following statements about grounding electrode conductors is true?A. They restrict the ground connection.B. They eliminate potential differences between conductive objects and the Earth electrode.C. They facilitate operation of overcurrent protective devices.D. They perform bonding between the Earth and grounded conductors.a.3. Main bonding jumpers are required to be made of _______ or other corrosion-resistant material.A. brassB. aluminumC. copperD. copper-clad aluminum