2. Fuel in Combustion chamber Turbine Net Power Air in Out Axial compressor Centrifugal compressor Exhaust Figure 1 Figure 1 shows the basic gas turbine cycle. Calculate the efficiency of the system if the temperature for the condition showed in T-s diagram below. Take that mass flow rate is 23 kg/s and the Cp is 35.5 J. K-l mol-". TA 8913 °C- 3 4987 °C 2 4665 °C- 1276 °C

2. Fuel in Combustion chamber Turbine Net Power Air in Out Axial compressor Centrifugal compressor Exhaust Figure 1 Figure 1 shows the basic gas turbine cycle. Calculate the efficiency of the system if the temperature for the condition showed in T-s diagram below. Take that mass flow rate is 23 kg/s and the Cp is 35.5 J. K-l mol-". TA 8913 °C- 3 4987 °C 2 4665 °C- 1276 °C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steam expands in a steam turbine isentropically from intet to exhaust having an enthalpy drop=1200 kJ/kg. Assuming ideal conditions determine the mean diameter of wheel if the turbine were of: (1) Single impulse stage. (i) Single 50% reabron stage.
Assuming the clearance is negligible for a single stage compressor with the following data.Atmospheric pressure: 90 kPaAtmospheric temperature: 17 ˚CDelivery pressure: 7 barFree air delivery flow rate: 0.2 m3/minTake “n” as 1.3, cp = 1.005 kJ/kg K, cv = 0.718 kJ/kg K 1.What is the power input to the compressor in kW to 3 decimal places if the compression reversible isothermal?
Air enters a turbine at temperature and pressure of 800°C, 10bar respectively. The actual exit airtemperature is 180°C. The turbine isentropic efficiency is estimated to be 85%. Calculate the turbine exit pressure and the actual expansion index (n).
10. The initial design of an IFR turbine is to be based upon Whitfield’s procedure for optimum efficiency. The turbine is to be supplied with 2.2 kg/s of air, a stagnation pressure of 250 kPa, a stagnation temperature of 800°C, and have an output power of 450 kW. At turbine exit the static pressure is 105 kPA. Assuming for air that γ ¼ 1.33 and R ¼ 287 J/kg K, determine the valueof Whitfield’s power ratio, S, and the total-to-static efficiency of the turbine.
A turbojet-powered aircraft is flying at 220 m/s and 8000-m altitude, where the ambient temperature and pressure are 236K and 35kPa, respectively.The pressure ratio of the compressor is 6 and the turbine inlet temperaturer is 970k. Estimate the thrust developed by the engine when the air flow rate is 55kg/s. employ an air standard-cycle analysis using the constant-pressurree specific heat c_p and specific heat ratio γ for air and neglecting the fuel properties.
Single stage, single-acting air compressor. Air delivery for this device is 30 bar at a speed of 1500 rev/min. The atmospheric condition of his location is 87 kPa and 20 ˚C, with a FAD of 0.22 m2/min. The clearance volume is 4% of the swept volume and the stoke/bore ratio is 1.3/1. Take “n” as 1.3, cp = 1.005 kJ/kg K, cv = 0.718 kJ/kg KW 1.What is the isothermal power of the compressor in kW to 2 decimal places in kW? 2. which formula will be used to evaluate the isothermal efficiency? 3. which formula will be used to evaluate the delivery volume? 4. What is the induced volume in terms of stroke volume, provide the coefficient values of the swept volume to 4 decimal places?
Specifications: Altitude = 700m Bypass ratio = 0.5 Speed = 260m/s Total mass flow rate = 15kg/s (in cold flow pipe) The pressure = 0.7bar (in cold flow pipe) Stagnation Temperature = 270K (at the turbine outlet) Stagnation gas pressure = 1.84 bar (at the turbine outlet) Temperature = 687.40C Both nozzles have a 95% efficiency For an aircraft powered by a low bypass ratio turbofan engine: 1a) For the flow expansion via the hot core nozzle, draw a T-s diagram. b) Determine the thrust produced by the hot nozzle. c) Determine the overall thrust produced by the turbofan engine and the thrust generated by the cold nozzle.
Answer this ASAP,thx In a gas turbine, air enters the compressor at a temperature of 290 K and a pressure of 100 kPa with a mass flow rate of 6 kg/s. The system pressure ratio is 10 and the exit temperature of each turbine stage is 1400 K. The efficiency of the compressor and turbine is 70% while the effectiveness of the regenerator is 70%. Value of K = 1.4, calculate A) thermal efficiency B) workback ratio C) net power generated
At a particular stage of a reaction turbine the mean blade speed is 140 m/sec and the steam is at a pressure of 20 bar with temperature of 250° C. Fixed and moving blades at this stage have inlet angles 30° and exit angles 20°. The stage efficiency is 80%. Determine (1) Specific entholpy drop across the stage in kJ/kg. (i) Drum Dia and blade height if heigh is one-twelfth of the drum dia. and the steam flow is 120 kg/sec. (ii) The percentage increase in the relative velocity across the bladings as a result of pressure drop across the blading.
The nozzle angle for an axial flow impulse turbine is 15°. The inlet absolutevelocity is 800 ft./s and the blade speed is 550 ft./s. Axial speed at the inlet andoutlet is assumed to be a constant. Calculate (a) energy transfer E, (b) change intotal (stagnation) and static enthalpies, (c) utilization factor.Ans: E=∆h0=245,038 ft-lbf/slug; ∆h=0; ε=0.77
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Here are the questions to be answered: 1. Why is the value of Wexp 0? (Explain) 2. Given the above values, can you calculate the Wflow? (Yes/No)
A blade pair in an axial flow compressor is being designed. The axial flow component of gas velocity is 174m/s. The engine diameter at the mean blade height is 0.73m and the blade height at the rotor inlet is 0.21m. The rotor's absolute inlet flow angle is 26 degrees. The stagnation conditions at the inlet to the blade pair are 298K and 130kN/m² Using Cp 1.005k/kg/K, R-0.287k/kg/K, and taking the ratio of specific heat capacities as 1.4, calculate the engine mass flow rate to the nearest kg/s