2. In the figure shown below, determine the following: Battery voltage = 240 volts a. The current in the battery, I,. b. The current in the 7-ohm resistor, k c. The current in the R-ohm resistor, b d. The current in the 18-ohm resistor, l. e. The current in the R-ohm resistor, Iy. Resistances are in ohms I2 7 42 I5 I3 12 R I4 18

2. In the figure shown below, determine the following: Battery voltage = 240 volts a. The current in the battery, I,. b. The current in the 7-ohm resistor, k c. The current in the R-ohm resistor, b d. The current in the 18-ohm resistor, l. e. The current in the R-ohm resistor, Iy. Resistances are in ohms I2 7 42 I5 I3 12 R I4 18

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

What is CEMF?
How is a solid-state diode tested? Explain.
The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
The 3-phase half-wave rectifier given in the figure is connected to 3-phase 380 380 V 50 Hz network and feeds 20 Ω ohmic load. Plot the average value of the current flowing through the load and the waveform (vdc) of the voltage across the load on the dashed curves given.
Answer the following questions according to the above. Remember Kirchhoff's laws when making your calculations in this question. a) According to the given graph, how many volts is the voltage value on it when this Zener diode is on a flat supply? b) According to the given graph, how many volts is the voltage value on this Zener Diode when it is on reverse supply? c) Calculate how many values V?−?? are when the zener current is 0 mA. D) Calculate how much the value of ??−?? is when the zener current is at its maximum value.
A half-wave rectifier has a 120 V rms, 60 Hz AC source. The load is a series inductance, resistance, and de source, with L= 120 mH, R= 12 £2, and Vdc 48 V. Determine (a) the power absorbed by the de voltage source, (b) the power absorbed by the resistance, and (c) the power factor.
Give a brief introduction about the topic of generation and measurement of direct current voltage...(if possible for 2 pg or 1 pg) high voltage engineering subject..
Notes on the verification of ohm's law by voltage method?
Using the Mathematical and Graphical Method, Determine the Qpoint and terminal voltages for the given circuit below. Compare the values from the two different approaches. Determine the terminal voltages and currents and the inter-electrode voltages.
A- Calculate the equivalent resistances (???) of the following circuits. (The resistance value of the diodes in the conduction will be taken as 0, the resistance values of the diodes in the insulation will be taken as infinity. R1=10 ohms) B- Explain P and N type items by drawing figures. Explain the element formed by the non-polar combination of these substances by drawing a figure.
Q1.Three-phase half wave rectifier supply resistive load with DC power of 4 kW; the ammeter connected with D1 indicates 8 A r.m.s current, and the source frequency is 50 Hz Due to system inductance the average voltage drops to 96.2% of idealized value ( when the inductance is neglected). How much will the average and r.m.s voltage s be? The r.m.s phase current and average load current Is=? & Idc=? The secondary r.m.s voltage and transformer capacity Vs & KVA? The inductances causes the voltage drop Lc=? The diode forward current and maximum inverse voltage? Now, if the phase B is failed ( disconnected), how much with new dc voltage be in %..Vdc=….% ??
What is a Semiconductor? Explain the properties of a Semiconductor such as its physics, etc? you better explain a little longer and illustrated pls